Question about Ford Cars & Trucks

Open Question

Ford sierra 3.0l V6 cylinder head torque settings

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3,0L Ford ranger 91 want shift into over drive.did before I pulled trans to replace rear main seal in Truck.please help


Overdrive is engaged with a torque convert clutch lockup. ATF travels through the splined shaft on the transmission to the torque converter. Check the seals on the converter and the trans.

Aug 25, 2015 | Ford Cars & Trucks

1 Answer

What is the torque wrench settings for 1992 sierra 2.0i dohc cylinder head


4 STAGES...

1.) 25
2.) 55
3.) +90 DEGREES
4.) +90 DEGREES

http://ford-euro.chat.ru/info/image/n8a.jpg

Aug 11, 2014 | Ford Sierra Cars & Trucks

2 Answers

Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex


The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

The torque specifications are as follows:

> Step 1: All bolts: 22 Ft Lbs (30 Nm.)
> Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

May 20, 2012 | GMC Sierra 1500 Cars & Trucks

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Cylider head torque specs ford windstar 1996 3,8 cylider V6


Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).


98c7056.gif

Oct 21, 2010 | 1996 Ford Windstar

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

Head bolt torque settings for a 1998 gmc 1500 5.o liter vortex


Cylinder Head Torque
1st - step, all bolts; - 22 ft./lbs. 2nd - step, long bolts; - turn 75 degrees 3rd - step, medium bolts; - turn 65 degrees 4th - step, short bolts; - turn 55 degrees fig121.png

Sep 04, 2009 | 1998 GMC Sierra

1 Answer

Ford-explorer 2005 v6 petrol cylinderhead tightening torques


a part place can give you a print out on the tor spec advance or auto zone

Jan 14, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...