I have a 2003 dodge stratus. There is a panic button on the keyless remote, which i lost sometime ago. The problem i am having is the panic will not turn off. i cant drive the car because the lights t

Maybe this will help you,
http://blog.carandtruckremotes.com/2015/04/09/free-programming-instructions-for-2001-2002-2003-2004-2005-and-2006-dodge-stratus-sedan-and-convertible-remote-keyless-entry-fob-alarm/

get the same one

I have a 2004 Dodge Durango. When I push the lock button it will lock door and set the alarm but the horn does not blow this is normal on my car. As Dodge is apart of Chrysler maybe it's the same for you, Unless in the past it did trigger the horn then the only thing I can think of is maybe there are different setting for your car. Check the owners manual. Hope this helps.

You must have one working remote to add one more to the system.
If you do not have one working remote right now then these instructions will not work.
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.


1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.
4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).
5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. Locks will cycle after each additional
remote is programmed.
6. Turn the ignition OFF and remove key.
7. Test Remotes.

the instructions say they are the same for up to 06. Need a working remote to make this work. On your programmed remote:
- Switch the ignition to the on position.
- Press and hold the Unlock button for at least four seconds. While holding this button, press the panic button and then release both buttons at the same time. You may or may not hear a chime from the vehicle.
- Within 30 seconds, on all remotes to be programmed (including the original "programmed remote")press and release the lock and unlock buttons at the same time, followed by pressing ANY button on the remote.
- Switch the ignition to off or wait 30 seconds for the programming mode to clear.

Just did it last eve; also can find more details in the Owners Manual (However you only need one working keyless remote to program another keyless remote. You should be able to use the electronic vehicle information center (EVIC) on the overhead console to train remote (Owner's Manual, p. 132-133). However, on my 2005 Liberty this does not show up as an option like it does on my 2003 Liberty.) or Jeep KJ Service Manual.

Hope it works for you (remember rated this help).

Horns are usually in front of the radiator and behind the grill--look for two of them, one on each side. Make sure they both sound. If only one works, there is a significant reduction in sound level. There may be road debris stuffed into the horn's throats--poke a hooked stiff wire into the throats and see if anything comes out. Most are sealed and can't be taken apart to clean--replacement is about the only recourse. (look in a wrecking yard for replacements)

If it is a factory remote it is either for the trunk release or the "panic" feature. Are the buttons not labeled?

try sec remote before replacing...keyless module in dash board

I have a 2003 dodge durango i dont have a working keyless remote how do i program one to kork.

does trunk button work? panic button?
here's 2003 info:

• The doors do not lock/unlock using the remote transmitter

• Remote transmitter.
• Driver door module (DDM).

• Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming

1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.

1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
   Press any button on the transmitter to be programmed.

1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

--------------------------------------------------------------
report back