Question about 2001 Isuzu Trooper

Open Question

My 2006 Isuzu 3L showed the check engine light and the engine stopped running. When checking fuel from the injector pump it only comes from the return pipes only. The engine does not start.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

honeymokey
  • 3113 Answers

SOURCE: 2004 Isuzu Rodeo 3.5ltr 4X4 hesitation/misfire acceleration

The upper intake gaskets may be leaking. They are made of plastic and metal and will leak air. Do not remove the cover on very top of manifold when changing.

Posted on Jul 24, 2009

  • 1 Answer

SOURCE: 2006 Isuzu 4x4 D-Max Chronic sensor problems "

perhaps this is:
replace EGR valve

Posted on Oct 04, 2010

ginko
  • 19396 Answers

SOURCE: 2001 Isuzu Rodeo 54248 miles

Hi.

If problem is only on startup and when idleing, then the problem is likely IAC system, also a vacuum leak will cause the same problem.

If problem is not only on startup and idle, but also when driving, then MAP sensor and EGR system must be checked.

Check also accelerator cable state and setting.


60549ef.jpg

The first thing to do is pulling out the OBDII fault codes stored in the ECM. This is done connecting a code reader to the ECM diagnostic port. The job can be done for a small fee at any local garage, and it is done for free at AutoZone.

The codes will help locating the problem.

About possible faults:

Problem is stalling when idling and during startup, but engine idling fast all the time. Problem not starting at times it is due to the fact that the wrong mixture is being sprayed, this is probably causing flooding and misfire. Since the CEL is on, one of the codes returned is probably misfire.

Check accelerator.

Check IAC system. This is composed by a valve and a solenoid that check and control amount of extra air air when the engine is idling. The IAC valve is located on top of the throttle body.

Check the vacuum system and try cranking with gas tank cap off. Vacuum system is tested using an hand tool gauge onvacuum lines while spraying card cleaner on the hoses (or heating them with a torch). If there is a leak, pressure will go up. A big leak will also do hissing noise, and will often result in a lean code when doing an OBD code scanning.

This kind of symptoms can also be caused by weak wiring to MAP/MAF sensor (MAP in this engine).

If the car also drives very rough and is revving up and down in a weird way, check the EGR valve.

As first thing I would do a code scanning. This car is OBDII. The scan can be done for free at the nearest Autozone, or for a small fee at any garage.

If you get any OBDII code from the scan, report it here, so that we can individuate the possible reason for the problem.

If you repute my solution helpful, then please take some times to accept the solution. Providing good repair tips requires time and skills, and your feedback is important for us.

Regards.

Ginko.

Posted on Oct 26, 2010

dttech
  • 4803 Answers

SOURCE: So my 1995 Rodeo will

First things first...Rewiring the fuel pump will only put a "Bandaid" on whatever the problem really is and will most likely create a situation where wires are draped across places where they shouldn't be, causing all kinds of future electrical problems. I have had to clean up that type of mess too many times.That type of "shade-tree" repair makes proper diagnosis and repair of a vehicle nearly impossible, even by a trained technician. My recommendation: DON'T EVEN THINK ABOUT IT!

OK, Now that I have my preaching out of the way...
The check engine light is supposed to come on every time you turn the key to the "On" or "Run" position before starting the engine. This is for a "bulb-check" just to let you know that it is not burned out. It should go out immediately after the engine starts and should stay off the entire time you are driving the car. It is not any type of indicator to let you know that the fuel pump has run. If your check engine light is not coming on every time you turn the key to "On", then there is probably a problem with your ignition switch or your ECM Main Relay. Either of these can cause an intermittent failure of the ECM to power up, a)d thus, not turn the check engine light on. Failure of the ECM to power up will also cause the fuel pump to not run because like the check engine light, the fuel pump is controlled by the ECM. (Rewiring the fuel pump will not make the engine start if this is in fact what the problem is.)

I have also seen many fuel pumps that run when they want to. You could have a bad fuel pump, but refering to your statement about the check engine light, I would guess that the fuel pump is not the main problem or even if it is a problem at all.

Posted on Dec 29, 2010

stevenhurc
  • 450 Answers

SOURCE: My Isuzu Bighorn 4JX1 RJM Engine stalled after

the engine oil pumps are in the rear of the engine(trans out) and behind flexplate /flywheel, were any of these 2 engine oil pumps touched if so the flywheel /flexplate has to be timed to crankshaft position, so you might have it in the wrong position, if your talking about the diesel lift pump (injector pump) that also supplies high pressure engine oil to injectors, after replacing this there is a learn procedure for the rail pressure control valve that is on pump. this can only be done by dealer or some one with Tech2 scanner tool.

Posted on Jan 22, 2011

Testimonial: "This was very helpfull and my car is now running. Thank you so much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How does a isuzu 250 freeighter get power on the dieselpump and injectors and trough witch fuse does it work


does it run? no symptoms stated just a hunt.
no year car(heavy truck)???

no country
why?
Freighter,
NPR or what? lots of trucks under Freighter,banner.
the 3L diesel
4JJ1-TC
direct injection type? correct? (and PCM to run it)
scan it after checking fuses?

we'd not spend all day looking free books
we see all fuse if they look bad,THEY ARE
if look good, test them , they can bad.
a voltmeter check is super fast.(key on)
if pump has power,why look for fuse.
filters clean
fuel lines primed.
if lift pump is it working?
scan the pcm for errors.
glow plugs ok.

Feb 24, 2017 | Isuzu Cars & Trucks

1 Answer

2006 isuzu kb 250 engine control wiring harness ?


the ECU/PCM lost power, you blew some fuses.

the CEL must glow , at first key on or the ECU is dead.
check fuses.

Aug 22, 2014 | Isuzu Pickup Cars & Trucks

1 Answer

Engine start problem


has the check engine light come on?
is it blowing any smoke when it starts and if so what colour?
has its servicing been kept up to date?
could be fuel related
check and drain water trap filter under vehicle look for any water contamination.
have the fuel filters been changed?
is it running rough at idle?
these had problems with EGR, injectors, and suction control valves as well as lift pump in fual tank that could cause your concern.
how many KM on clock?

Apr 03, 2014 | Isuzu Pickup Cars & Trucks

1 Answer

Check engine sign flashing. i have an auto repair shop and encountered lots of this with isuzu dmax. engine doesn't start. no fuel coming out of the injection pump. please help!!!


first of all check the fuses
check to see if there is any spark, no spark check ignition system
check fuel pressure, no pressure then check fuel pump
if there is pressure and spark then check to see if fuel injectors work
if no spark and no fuel injector check crank sensor, ignitor and wirings

Feb 27, 2010 | 2004 Isuzu Rodeo

1 Answer

1KZ-TE Toyoto 3L TDi in Granvia Engine Warning Light comes on with hard accelleration when hot and maximum speed steadily lowers to 30mph.Code shows for "low fuel-pressure". Filter changed, pipes all clear...


Install fuel pressure guage, clamp off return side and verify the exact pressure it is producing to the injector rail. Checkmanufacturer specs. If it is not sufficient. Replace pump.

Aug 25, 2009 | Toyota Passenger Cars & Trucks

5 Answers

Dodge cummins won't start, fuel reaching injector pump but no fuel coming out of injector pump.


You said you have fuel flowing from the inlet line of the injection pump? But not at the injector lines?

May 05, 2009 | 1999 Dodge Ram

3 Answers

4JX1 engine cut off while test drive after oiland filter change and not starting


That pop noise is ok just the flap in the throttle body coming open when the car stops .
The engine may have stopped because its low on oil so the oil pump for the injectors wont work - takes about 7 u.s. quarts of 5/30 fully synthetic oil at service time to run right.
It can also stop if the pressure sensor in the injector rail packs up or the oil pick up pipe for the injector system falls off due to cracking the mount .

Oct 28, 2008 | 1999 Isuzu Trooper

Not finding what you are looking for?
2001 Isuzu Trooper Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...