Question about Jeep Cherokee

Open Question

Cylinder head bolts size 2001 jeep cherokee - Cherokee Jeep Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: What is the tension on cylinder head bolts for a

Would like to state the cylinder head Torque Values, Torque Pattern, and Tightening Sequence, plus additional tips.
[I know it's more than you asked for, but after you read the entire answer here, I believe you'll know why I stated it this way]

Torque Pattern:
Top of head starting from Left going Right,
8, 4, 1, 5, and 9
Bottom of head, (Exhaust manifold side), starting from Left going Right,
7, 3, 6, 2, and 10

You're supposed to use old bolts with the head cut off, (Alignment Dowels), in bolt holes 8 and 10. This way you goop the gasket, and install it, then slide the head on. Place the head bolts in, SNUG them down. Remove those alignment dowels. Then put bolts 8 and 10 in place.
After the head of the bolt is cut off, you saw a slot in the top of the bolt. Helps when you remove it. (Have any old bolts that are long enough for this, and have the correct threads?)

=>Coat No.7 bolt with thread sealant.

Tightening Sequence:
Step 1: Tighten all bolts to 22 Foot Pounds. (30Nm) (Using the above Torque Pattern)

Step 2: Tighten all bolts to 45 Foot Pounds. (61NM)

Step 3: Tighten 1 Through 6 <- to 110 Foot Pounds. (149Nm) DO NOT TIGHTEN No.7 bolt yet!

Step 4: Tighten No.7 bolt to 100 Foot Pounds. (136Nm) DO NOT TIGHTEN further! It only tightens to 100 Ft.Lbs. (136Nm)

Step 5: Tighten bolt 8 Through 10 to 110 Foot Pounds. (149Nm)

Step 6: Repeat Steps 3 , 4, and 5


Posted on Sep 05, 2009

  • 29 Answers

SOURCE: 2001 Jeep Cherokee with 6 cylinder engine -- PO306 code cylinder

Plug, plug wire, plugged or open fuel injector. are the most likely.

Posted on Sep 28, 2009

c17hydro
  • 2984 Answers

SOURCE: what is the cylinder head torque on a 2001 jeep

Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Posted on Mar 06, 2010

fingaz22
  • 1068 Answers

SOURCE: what size are the head bolts for 1998 jeep

13mm 12 point socket.

Posted on Apr 18, 2010

emissionwiz
  • 75066 Answers

SOURCE: WHAT IS CYLINDER HEAD BOLT TORQUE ON A 1988 JEEP

Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side.

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head bolts


try a 15 mm socket

Oct 12, 2013 | Jeep Cherokee Cars & Trucks

1 Answer

Rear caliper bolt size 2001 jeep grand cherokee laredo


If you mean to remove bolt, they are a metric allen size. To replace, you need a special pin / sleeve type bolt, available in sets at the auto parts store for around $14.

Jun 19, 2011 | 2001 Jeep Grand Cherokee

1 Answer

I am looking for the head bolt torque specifications and sequence for a 1988 jeep Cherokee 4.0 i6


zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Mar 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

What is the cylinder head torque on a 2001 jeep cherokee


Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Mar 06, 2010 | 2001 Jeep Cherokee

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...