Question about 2003 Ford Explorer Sport Trac

Open Question

Location of neutral safety switch on dodge ram 1500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 99 Answers

SOURCE: LOCATION OF SAFTEY NEUTRAL SWITCH ON 66 MUSTANG

if it is a manual trans it is in the clutch arm under the dash and if automatic it is at the base of the steering column

Posted on Nov 30, 2008

Ad
canbruce75
  • 1776 Answers

SOURCE: removing neutral safety switch

Check out the autozone website at autozone.com and register your vehicle. It is free and will give you access to an online repair manual for the vehicle. The steps for removing the neutral safety switch can be found there. Hope this helped. Best wishes.

Posted on Aug 03, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

drsinister69
  • 2317 Answers

SOURCE: where is the neutral safety switch?

Should be mounted on the drivers side of the transmission, usally behind the shifter lever coming out of the transmission.

Posted on Mar 07, 2010

techbuster
  • 5081 Answers

SOURCE: where is the neutral safety switch located on a

If manual it is on clutch peddle assembly.
If automatic it is on the transmission where shift linkage connects to trans.

Posted on Oct 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you find the neutral switch in a dodge ram 1500 truck.


The neutral safety switch is on the transmission next to the transmission shifter shaft and unscrews after you unplug the wiring harness.

Dec 13, 2014 | 2000 Dodge Ram 1500 Truck

1 Answer

Replacing neutral safety switch


The automatic models use a pressure switch that screws into the side of the transmission. You can look the part up online to get a visual.

Jul 01, 2013 | Dodge Ram 1500 Cars & Trucks

1 Answer

Starter will not start in forward manual gears,


Neutral safety switch. Its purpose is to allow starter to engage in Neutral ONLY

Apr 05, 2010 | 2006 Dodge Ram 1500

1 Answer

My 1998 Dodge 1500 4x4 will only start with the shifter in neutral.What's the problem?


neutral safety switch or cable/linkage out of adjustment let me know please

Mar 18, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

I am looking for the location of the reverse light switch on my 1999 dodge ram 1500 pickup.. It is an automatic transmission..


Look around shift linkage area of transmission for a threaded in plug with 3 or so wires to it. Neutral safety & back-up are in one switch.

May 08, 2009 | 1999 Dodge Ram

3 Answers

1998 Dodge Ram 1500 back up lights


The back up /neutral switch is on the left side off the transmission.
Go on your back under the car (steerside) and there it as.


Greetings .
Victor

Oct 16, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
2003 Ford Explorer Sport Trac Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...