Question about Chevrolet Cars & Trucks

Open Question

2006 monte carlo dtc code p1258 - Chevrolet Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: 2006 monte carlo stuck in park

sometimes if the steering wheel is locked it won't come out of park try applying on the brakes and at the same time move the wheel back and forth and if this does not work and you have tilt it may be a problem in the steering column

Posted on Jan 21, 2009

Ad
  • 1 Answer

SOURCE: 2006 Monte Carlo

Here's how to override the shift lock on a 2006 Monte Carlo. First, remove the top of the shift console by pulling up on the plastic piece directly in front of the hinged cover. This is the piece that has the cup holders molded into it and it is held in place by 4 clips (i.e. it will pop back into place with no tools).

Next, shine a flashlight down into the console to the right of where the shift lever passes through (passenger's side). You'll see a wiring clip with 4 or 5 wires going into it. Directly behind this clip you can see a metal shaft with a flared top that looks like a button. This is the shift lock override button. Reach in behind the wiring clip with your right hand and press this button in. With the engine running, hold the button in with your right hand, press on the brake, and shift out of park with your left hand.

Now you can drive the car to your mechanic (or to your own garage) to find out why the shift lock solenoid is not working. On mine it was obvious. A wire going into that clip near the override button came loose and there was no power to the shift lock solenoid. I removed the clip, reattached the wire, and replaced the clip. Problem solved, fixed for free!

Posted on Feb 21, 2009

ourhowse
  • 2007 Answers

SOURCE: belt diagram for a 2006 chevy monte carlo

There should be a decal on the bottom side of your hood, or somewhere in the engine compartment. If there isn't just put it on the crankshaft (bottom pulley) and go ribs to ribs, and flats to flats, and work your way around.

Posted on Jun 10, 2009

  • 141 Answers

SOURCE: serpentine belt diagram

should be in the owners manual if not under hood....new goodyear belts also have diagrams on the back of them....

Posted on Aug 09, 2009

  • 83 Answers

SOURCE: 2006 monte carlo key stuck in ignition what to do?

You can try 3 things:

1. Make sure the vehicle is fully in PARK if an automatic, and in GEAR if a standard.

2. If key does not come out, wiggle the steering wheel back and forth as you try to remove the key. Making sure the key in completely in the OFF position.

3. Bring the vehicle to a dealership, they can fix the problem.

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 monte carlo stereo turns on but there is no sound? I have tried turning it off and the car off and i recieve cal err


Sorry dude but your going to have to take to the dealer !
DTC B1001 DTC B1025, B1035, B1045, or B1055 DTC B1259 DTC B1780
The radio does not function properly. The radio displays "CAL".
Install a scan tool. Turn ON the ignition, with the engine OFF. With the scan tool, perform the radio setup procedure. Refer to Radio Setup . Turn OFF the ignition. Turn ON the ignition, with the engine OFF.

Oct 20, 2016 | 2004 Chevrolet Monte Carlo

2 Answers

Monte carlo 2006 the radio is lock cam you help to unlock


notify dealer with vin and proof of ownership for lock code

Sep 19, 2016 | 2006 Chevrolet Monte Carlo

1 Answer

Car stuck in park


    Help! Shifter stuck in park - Monte Carlo Forum - Monte Carlo ...

    montecarloforum.com > ... > Engine/Transmission/Performance Adders
    Jul 20, 2010 - I'm new here and desperately need some help with my 2006 Monte. ... ofpark. Tried rocking car back and forth but it seems to be the switch or solenoid that stops car from going into gear without ... 1984 Chevrolet Monte Carlo. Trans Stuck in Park - Monte Carlo Forum - Monte Carlo Enthusiast ...
    Apr 28, 2013
    gear shift locked up - Monte Carlo Forum - Monte Carlo Enthusiast ...
    Aug 17, 2012
    Getting stuck in park - Monte Carlo Forum - Monte Carlo ...
    Dec 12, 2011
    HELP!!!! My KEY is STUCK IN IGNITION - Monte Carlo Forum
    Jun 20, 2011
    More results from montecarloforum.com

Dec 16, 2015 | 2006 Chevrolet Monte Carlo

1 Answer

Code p0011


You need 2 replace a part called the magnet it advances the crank shaft get it from the dealer

Aug 05, 2014 | 2006 Chevrolet Monte Carlo

1 Answer

Check engine light, low engine power


You get a reduced power message ? Your vehicle has electronic throttle control or also known as drive by wire . Your gas pedal is electrically hooked to the PCM - engine computer . Has two position sensors inside as does the throttle body on the engine . Over time these position sensors wear an cause improper signals to the computer an the computer will put the vehicle into a limp mode . Most cases it will drive but only at about 20 mph . There are videos on youtube showing how this works , how to diagnose etc....
This P0449 is something different , has to do with the Evap. emissions .
DTC P0449 Evaporative Emission (EVAP) vent Solenoid Control Circuit . Planty of videos on youtube for GM trucks on this problem .
DTC P1516 Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance
The predicted throttle position (TP) is compared to the actual throttle position. The two values should be within a calibrated range of each other. Both the powertrain control module (PCM) and the throttle actuator control (TAC) module redundantly monitor the predicted and actual throttle position. DTC P1516 sets if the PCM detects an out of range condition between the predicted and the actual throttle position.
Look's like you have three different problems , Thought p1516 an p1258 were going to point to same electronic throttle problem .

P1258
Engine Coolant Overtemperature - Protection Mode Active
PCM
DTC P1258

Circuit Description
The powertrain control module (PCM) uses the ECT sensor to monitor the engine for an over temperature condition. This condition occurs when the coolant temperature is above 132°C (270°F). When an over temperature condition is present, DTC P1258 will set. The PCM will disable two groups of four cylinders by turning OFF the fuel injectors. By switching between the 2 groups of cylinders, the PCM is able to reduce the temperature of the coolant.

Check the engine cooling fans for proper operation.
Are the engine cooling fans operative? Have you ever had the thermostat changed ? Is the coolant full ?

Check out youtube videos ! Just type your codes into the search bar .

May 02, 2017 | 2006 Chevrolet Silverado 2500HD 2WD

1 Answer

Where is my upstream O2 sensor on 2006 Monte Carlo?


It is the one that is before the catalytic converter

Nov 02, 2012 | 2006 Chevrolet Monte Carlo

1 Answer

The reduce engine light comes on at 50 mph what could the problem be


DTC P0120 P0220 P1516 P2135 these should be the problem codes.
2003-2006 Chevrolet Avalanche, Corvette, Express, Monte Carlo, Silverado, SSR, Suburban, Tahoe, Trailblazer. for reduced engine power. p0120 is throttle position sensor, ( tps ). p0220 is relates to tps, p1516 tps is out of range. p2135 is a throttle body code, the throttle body needs replaced. but before you do it replace tps first to see if it takes care of the other codes. have a good day !!

Feb 18, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

P1258 CODE


Trouble Code: P1258 (4.6L V8 VIN 9 Auto)
Engine Metal Over-Temperature Protection
Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
DTC P0117, P0118 and P0125 not set, Engine started; and the PCM detected the ECT sensor indicated more than 270ºF for 10 seconds. The PCM uses the ECT sensor to detect if the engine is running too hot (when the ECT sensor is over 268ºF). If the engine is overheated, DTC P1258 will set. The PCM will disable 2 groups of four cylinders by turning off the fuel injectors. By switching between the two groups of cylinders, the PCM is able to reduce the temperature of the coolant and lower the temperature.

Possible Causes:
  • Engine cooling system problem (test the cooling fan operation)
  • Engine coolant level is low or the mixture is not correct
  • ECT sensor is out-of-calibration or "skewed"

Aug 13, 2010 | 1999 Cadillac DeVille

1 Answer

2006 monti carlo blower motor stuck on high, even


what blower you talking about.if ac blower your blower relay stuck close. your monte carlo has a super charger blower also.

Jul 05, 2009 | 2006 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...