Question about Cars & Trucks

Open Question

2006 GMC canyon P0651 diagnostic code - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ftw1952
  • 10319 Answers

SOURCE: how do I replace a 2006 gmc canyon brake light

yes you can.... it is a plunger style switch located near the brake pedal inside the car

Posted on Feb 28, 2010

Ad
  • 10865 Answers

SOURCE: how to fix the Tailgate Handle on a 2006 gmc

Hello. This is not difficult. Order the part or buy it at a GMC dealership. It will come with instructions.

Posted on Mar 02, 2010

melvi_99
  • 387 Answers

SOURCE: What is the most likely problem for codes POO14

this is set from camshaft and crankshaft sensor, always check engine oil for the right vescocity and change oil if necessary to avoid this dtc set

Posted on Jul 20, 2010

  • 11 Answers

SOURCE: 2006 gmc envoy denali xl check engine on,did

possilbe fuel level sensor

Posted on Sep 10, 2010

SOURCE: How do I do an oil change for 2006 GMC Canyon?

Lift your GMC Canyon using a jack and set the truck on jack stands. If you don't have jack stands then use a set of wheel ramps. Make sure you brace the front tires so the truck doesn't roll. (safety first) Pop the hood and take off the oil filler cap and remove the dipstick. Gather an oil drip pan, cleaning cloths, new oil filter, and adjustable crescent wrench and then slide under the truck. Locate the oil drain plug and filter. Loosen and then remove the oil plug and pull it out quickly. Let the used oil drain for 10 to 15 minutes into the drip pan. Take off the filter using an oil filter wrench. Check the gasket and threads for damage and dump the extra oil into the drip pan. Clean off any excess oil and replace with new oil filter. Put the oil drain plug back in (tighten it) and slide out from underneath your truck. Add new oil (approx 5 quarts) inside the oil filler hole and replace the dipstick and then tighten the oil cap. Lower your truck and start the engine for a minute so that oil pressure builds up. After you are done with the oil change, turn the ignition key to "run" and then hit the gas pedal three times to reset the oil change light.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a 2008 GMC Envoy Denali, 2WD. Yesterday the engine would barely idle and numerous lights on the dash came on including the check engine light. I had a friend check the diagnostic codes and it came up...


Five days prior to this, the battery had to be replaced. The engine was started without the pause for two minutes ?????? Where do you people come up with some of this stuff ? Pausing for two min. before starting has nothing to do with it . DTC P0651: 5-Volt Reference 2 Circuit
Some of the engine sensors on your vehicle work off of a steady 5 volt supply by the PCM - engine computer . One of these sensors is short internally bring down the PCM .
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Accelerator Pedal Position (APP) Sensor 1 5-Volt Reference 2 Circuit
P0651
P2122
P0651
--
Accelerator Pedal Position (APP) Sensor 2 5-Volt Reference 1 Circuit
P0641
P2127
P0641
--
Air Conditioning (A/C) Refrigerant Pressure Sensor 5-Volt Reference 1 Circuit
P0641
P0532
P0641
--
Camshaft Position (CMP) Sensor 5-Volt Reference 1 Circuit
P0641
P0340
P0641
--
Engine Oil Pressure (EOP) Sensor 5-Volt Reference 1 Circuit
P0641
P0522
P0641
--
Fuel Tank Pressure (FTP) Sensor 5-Volt Reference 1 Circuit
P0641
P0452
P0641
--
Manifold Absolute Pressure (MAP) Sensor 5-Volt Reference 1 Circuit
P0641
P0107
P0641
--
The Crankshaft Position (CKP) Sensor 5-Volt Reference 2 Circuit
P0651
P0335
P0651
--
Throttle Position (TP) Sensor 1 and 2 5-Volt Reference 2 Circuit
P0651
P0122, P0222
P0651

That's why it wasn't running good ,an lights lit on the dash. Your best bet , take it to GMC dealer .
No where in GM service info does it say after replacing the battery that you need to wait two min. before starting .
Position the positive battery cable (1) to the battery.
Tighten the positive battery cable bolt.
Tighten
Tighten the bolt to 15 N·m (11 lb ft).
Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

Aug 02, 2017 | GMC Cars & Trucks

1 Answer

2006 gmc canyon will not go into 4 wheeldrive after 5 minutes of driving


The first place to start is have it checked for codes an to see if a scan tool will communicate with the 4X4 control module !
Diagnostic Starting Point - Transfer Case
Begin the system diagnosis with the Diagnostic System Check - Vehicle . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control module or modules that command the system.


?€¢
The ability of the control module or modules to communicate through the serial data circuit.


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and the status of the codes.

The use of the Diagnostic System Check - Vehicle will identify the correct procedure for diagnosing the system and where the procedure is located.
Install a scan tool.
Does the scan tool power up?
Go to Step 3
Go to Scan Tool Does Not Power Up

3

  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to establish communication with all of the control modules on the vehicle. Refer to Scan Tool Does Not Communicate with Class 2 Device for the modules you should expect to observe.
Does the scan tool communicate with all of the expected vehicle control modules?
If you don't have a scan tool that will communicate with all modules on the vehicle or understand this , your best bet is to take it to a ASE certified repair shop or the dealer .

Jan 07, 2016 | 2006 GMC Canyon Crew

1 Answer

Locked radio 2006 gmc canyon


Most modern cars have a security code enable for the installed radio/cd players. This is an anti-theft device.

The initial documents given to the owner when the vehicle was purchased lists this code and how to reset it.

If you are second owner/original owner who has lost this information, then, you can approach gmc canyon dealer and they will have this code on their server. Normally a free service (I believe).

The security code is lost from the radio whenever keep alive voltage is removed from the radio. i.e. You disconnected or replace the battery.

I hope this helps.

Jul 23, 2014 | 2006 GMC Canyon

1 Answer

My GMC canyon truck 2006 is running very rough. I did a diagnostic test at the part store, and the codes P0300, P0017, P0068, came up. The dash control panel says reduced power.


Code 300 is for a random miss, code 17 is for a problem with the timing between the cam and crank sensors, and code 68 is a problem between where the throttle position sensor is and the amount of air coming into the throttle body.
You may need to research the trouble codes to get the testing procedures. You may also need a scanner to do the tests.

Sep 15, 2012 | 2006 GMC Canyon

1 Answer

What is the most likely problem for codes POO14 and POO17 on a 2006 GMC Canyon with a 3.5 engine?


this is set from camshaft and crankshaft sensor, always check engine oil for the right vescocity and change oil if necessary to avoid this dtc set

Jul 20, 2010 | 2006 GMC Canyon

1 Answer

How to fix the Tailgate Handle on a 2006 gmc canyon truck


Hello. This is not difficult. Order the part or buy it at a GMC dealership. It will come with instructions.

Mar 02, 2010 | 2006 GMC Canyon

2 Answers

GMC Canyon, computer shot.. cost?


You can to the Salvage Yard for a new computer, but your going to have to get it reprogram to your ignition keys, so the Passlock will start the engine. Before you go through all of that. recheck every thing, it could be your crank sensor or your ICM faulty causing your engine to shut down. Keep me posted and let me know what DTC codes you have. Note: a faulty fuel pump or dirty fuel filter will not set a DTC code. You may have a dirty fuel filter or faulty fuel pump or faulty fuel pump wire harness or fuel pump relay.

Jan 24, 2010 | 2006 GMC Canyon

2 Answers

2006 Gmc canyon, acts like not getting fuel on starting up ,can hear fuelpump running,changed relays around and truck cranks.


run scanner for trouble codes, some auto parts store will do this for free, check all fuses

Oct 04, 2009 | 2006 GMC Canyon

1 Answer

2006 Canyon 4cyl has extremely low idle. Autozone Diagnostics gives code:P0506. Idles low if at all.


Could be:
  • A vacuum leak
  • An air restriction in the intake air path or exhuast
  • A faulty positive crankcase ventilation (PCV) valve
  • Damaged/failed/dirty throttle body
  • Internal engine problem
  • Failed PCM (powertrain control module)
I say back to the shop if its a real problem, if at all to just clear the code to see if it comes back. That code is just an informational code. Just says what the car is doing :\ . My first guess would be a vacuum leak somewhere followed by a throttle body issue.

Sep 15, 2009 | 2006 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...