Question about 1998 Ford Mustang

Open Question

Ford mustang wont start completely dead even keyless entry will not work

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
warlock61
  • 659 Answers

SOURCE: keypad keyless entry code missing

Ford has an add on keypad also if it is pretty much flush on the door it is factory if it is a fat keypad it is an add on The factory module is under the dash by the fuse panel the number should be on it

Posted on Nov 22, 2008

Ad
chuck943
  • 783 Answers

SOURCE: CHANGE CODE ON KEYLESS ENTRY SYSTEM FORD EDGE

Yes you can program your own code by inputting the original code then hit the no. 2 button then input your own 5 digit code.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: need keyless entry code for a 04 an 99 ford explorer

On your 99 model the module is located behind the left quarter trim panel,mid-way.You maybe able to see it by removing the speaker cover or the cupholder on top. The module will have a sticker with a 5 digit code.
On the 04 the model is behind the right quarter trim panel toward the front about even with the right rear door stricker.

Posted on May 17, 2009

  • 93 Answers

SOURCE: Keyless remote wont work

try to reprogram the remotes using these instructions..........
i assume for 02 explorer not th 05 frestyle listed (although similar procedure)
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.

  1. Make sure that the anti-theft system is not armed or triggered and key code programming is not active.
  1. Open the door, then press the driver door lock control switch UNLOCK button.
  1. Turn the key from OFF to ON 8 times within 10 seconds, with the eighth turn ending in ON. If the program mode is sucessfully entered the doors will lock and unlock to confirm.
  1. Press any button on a remote transmitter, and the doors will lock and then unlock all doors to confirm that the remote transmitter is programmed. All remote transmitters must be programmed within 20 seconds of each other. Up to four remote transmitters can be programmed to the vehicles security module each time programming mode is entered.
  1. If the door locks do not respond for any remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Locks, Latches and Entry Systems — Late Build or Locks, Latches and Entry Systems — Early Build in this section.
  1. NOTE: Exiting is acknowledged by locking and unlocking the doors if at least one remote transmitter has been programmed.
    Exiting the programming mode is accomplished if one of the following has occurred:
    • The key transitions to OFF.
    • 20 seconds have passed since entering programming mode or since the last remote transmitter was programmed.
    • Four remote transmitters have been programmed.

Posted on Jun 02, 2009

  • 93 Answers

SOURCE: how to reset factory code on keyless entry ford five hundred

if you do not already know the factory code, the only way it can be obtained is by your local ford dealer. the proprietary computer equiptment they have can access the code that is programed in vehicles security module. if you purchased it used..it is often that the keyless entry code id card is still withe the owners manual..it is a 5 digit code printed on an credit card sized card that is white in color..i hope this helps you...good luck

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCodeā„¢ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In Ā· Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

1 Answer

Does my 1998 mustang ls have and alarm and how do i activate it


If it doesn't have a wiring problem the keyless entry is how you turn the alarm on.
check the batteries make sure the key less entry is programmed to your car.
If it's a GT it should have an alarm

Jul 06, 2014 | 1998 Ford Mustang

1 Answer

2003 ford escape failed to start; jump start was successful, but before that could happen, I noticed keyless entry not working, radio/clock completely dead, dome lights not working even with car running.


all those radio .ketless entry all inside are run by a body control module that is locator under the dash in the center behind the radio. do not confuse it with the ecu, the ecu is under the hood

Aug 27, 2013 | 2003 Ford Escape

1 Answer

2006 Ford Mustang GT wont start. Passenger side lights always stay on. Keyless remote wont open doors, trunk or sound the alarm (I checked the keyless remote battery it still has juice) When I turn the...


From the clicking sound and the fact that alot of your cars systems are down i would say that your battery is dead, if not bad altogether, or a terminal is loose on the battery. Check the terminals on your battery (be careful with the + (red) side and do not touch anything else metal on the car or the - (black) pole while touching it or just disconnect the - (black) for safetys sake). Check the terminals for looseness or corrosion and repair as neccisary. Then try a jumpstart but do not let the car "click" too much or you will burn out your starter. If your car's battery is indeed dead/bad you will find out within the next few times you try to turn on your car (it simply wont turn on) take the battery to a auto parts store and ask them to do a test. If the battery is ok then you can have it recharged if its bad then you will need a new one.

Dec 20, 2010 | 2006 Ford Mustang

2 Answers

My 2004 v6 ford explorer won't start new batery and new starter no luck wont even click ?


Did you check the start relay for voltage? Ohms reading?

If I remember correctly the circuit goes like this:
Key turns ignition switch which puts voltage to the start relay which engages the solenoid.
So if it isn't even clicking and your headlights seem to be working fine then it is either the ignition switch or the start solenoid coil.
On older Fords the start solenoid used to be remote mounted on a fender. I heard newer Ford vehicles had it integrated with the starter like GM does.
A quick visual inspection will tell you which and where you need to look.
You might check if there is a fuse for that as well.

Apr 01, 2010 | 2004 Ford Explorer

1 Answer

My powerlocks on my mercedes 2000 s500 wont repond to my keyless entry


REMOTE KEYLESS ENTRY BATTERY IS WEAK OR DEAD.YOU HAVE TO LET DEALERSHIP REPLACE KEYLESS ENTRY AND REPROGRAM IT TO UNLOCK OR LOCK DOORS.

Oct 17, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

How can i tell if my 95 mustang has keyless entry when i got it I only had one key I seen some remotes online for sale and would like to get one if they will work


Keyless entry is the number keypad on the driver's door. It more than Likely that if your mustang has power windows, it has remote unlock via a key chain remote. You can get replacment remotes either at a dealer or online... they're not to complicated to pair up with your car.

Jun 09, 2009 | 1995 Ford Mustang

2 Answers

CLock, radio, dome lights, speedometer, keyless entry dont work


Check fuse 8 (10 amp fuse) in the under dash fuse panel. Make sure you have voltage to it on both sides of the fuse.This fuse feeds all of the items you listed.

May 25, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
1998 Ford Mustang Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...