Question about 2006 Volvo S40

Open Question

Anti sladd service - 2006 Volvo S40

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 Chrysler Sebring started and turned off three times now, it just has a blinking red light?


Anti-Lock Warning Light (ABS) - If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required, however, the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. 24 7 Locksmith Orchard Park NY 716 710 7400 Locksmith Orchard Park NY

Aug 11, 2016 | Chrysler Sebring Cars & Trucks

1 Answer

Anti skid services required or anti skid services off


battery almost done,gave me that code on mine,also brake failure

Dec 29, 2014 | 2008 Volvo XC90

1 Answer

Need to flust anti freeze.Anti freeze is a thick ,gummy texture..


if the anti freeze is not serviced regularly the dexcool will start sludging up the system
if the old type (green)anti freeze was added this will also cause the same.
drain system completely & add water,run for 10 -15 minutes & drain.do this a couple times
& then add a good flshing agent with the water.you may need to do this several times with
flushing material.after it looks better.add anti freeze & consider reflushing 1K miles or so
dont forget to bleed the system of air. bleeder valve(flat head screw) near thermostat

good luck

Jun 22, 2011 | 2004 Pontiac Grand Prix

1 Answer

I have a 07 chevy tahoe 5.3L now its showing me service anti-theft... i turn my key and nothing happens it just shows service anti-theft..


Anti theft security systems are tricky. Expensive to fix and harder to diagnose. I've had the best luck with just bypassing the entire system and never worrying about it again. There is tons off info and some "do it yourself" solutions on this site http://vatspasslockpasskeysecurityhelp.yolasite.com/

May 17, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

My car is saying service anti theft . How do I service the anti theft myself?


You service it by taking the car to Cadillac for the servicing of the anti theft

Jan 22, 2011 | 2001 Cadillac DeVille

1 Answer

1999 Buick century anti lock signal and trac off displayed when traveling over 60 miles per hour


You will be best off bringing the car in for service. If the anti-lock signal comes on, it means that your ABS system has a fault and you do not have anti-lock brakes functioning. When the light comes on the car runs on your brakes alone, no anti-lock.

To check the codes and the ABS system, the car should really be serviced.

Good luck!!
EJ Kudelka

Nov 20, 2010 | Buick Century Cars & Trucks

1 Answer

I have a 2005 GMC Savana G3500 and I need to know how many O2 sensors there are and where they are. Can anyone help?


Oxygen Sensor
Removal & Installation
CAUTION
The oxygen sensor in-line connector and
louvered end must be kept clear of grease, dirt or other contaminants. Avoid
using cleaning solvents of any type. DO NOT drop or roughly handle the oxygen
sensor.
The oxygen sensor may be difficult to remove when the engine
temperature is less than 48°C (120°F)

NOTE: Removal of the oxygen sensor is
easier when the engine temperature is above 48°C (120°F).

Upstream HO2S Sensor
To Remove:


  1. Before servicing the vehicle refer to the Cautions and
    Warnings at the beginning of this section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    • Electrical harness connector (A) from the HO2 S.
    • Remove the HO2 S (B) using special service tool
      J39194-B.





gm_exp_oxy_snsr_upstrm.gif

To Install:

CAUTION
GM uses a special anti-seize compound on the
HO2S threads. The compound consists of liquid graphite and glass
beads. The graphite tends to burn away but the glass beads remain easing sensor
removal. New or service replacement sensors have the anti-seize compound already
applied to the threads. If the sensor is removed from an exhaust component and
if for any reason the sensor is to be reinstalled the threads must have
anti-seize compound applied before installation.


  1. Coat the HO2 S threads with GM P/N 5613695
    high-temperature anti-seize compound as needed.
  2. Install the HO2 S using special service tool
    J39194-B;

    • Torque to 31 ft-lbs (42 Nm).

  3. Connect the HO2 S electrical harness connector.
  4. Lower the vehicle to the ground.

Downstream HO2S Sensor
To Remove:


  1. Before servicing the vehicle refer to the Cautions and
    Warnings at the beginning of this section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    • Electrical harness connector (A) from the HO2S.
    • Remove the HO2 S (B) using special service tool
      J39194-B.





gm_exp_oxy_snsr_dwnstrm.gif

To Install:

CAUTION
GM uses a special anti-seize compound on the
HO2S threads. The compound consists of liquid graphite and glass
beads. The graphite tends to burn away but the glass beads remain easing sensor
removal. New or service replacement sensors have the anti-seize compound already
applied to the threads. If the sensor is removed from an exhaust component and
if for any reason the sensor is to be reinstalled the threads must have
anti-seize compound applied before installation.


  1. Coat the HO2 S threads with GM P/N 5613695
    high-temperature anti-seize compound as needed.
  2. Install the HO2 S using special service tool
    J39194-B;

    • Torque to 31 ft-lbs (42 Nm).

  3. Connect the HO2 S electrical harness connector.
  4. Lower the vehicle to the ground.

Sep 23, 2010 | 2005 GMC Savana

1 Answer

Brake fluid and anti freeze


DOT Type 3 or better. Look at the brake fluid cap - it will tell you there.

Anti freeze? Go to your full service auto parts store or your authorized Ford Dealer to get the proper anti freeze for your Expedition.

thanks for your question at FixYa.com

Jan 06, 2010 | 2005 Ford Expedition

1 Answer

The service light, anti lock light, and traction


you most likely have an ABS problem you will need to have it scanned to get the code

Dec 06, 2009 | 2004 Oldsmobile Alero

1 Answer

What does the anti lock light on the dash mean?


The anti-lock light is indicating that your anti-lock brake system has a problem. Check fluid level. Could be a sensor, time for brake service etc, but I wouldn't wait too long to have it checked, just in case something serious. Anti-lock brake problems may cause a wheel or more, or all, to lock up in a panic stop situation. When was last service on brakes done?

Apr 25, 2009 | 1997 Chevrolet Lumina

Not finding what you are looking for?
2006 Volvo S40 Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...