Question about 2004 Chrysler Pacifica

1 Answer

Getting p0340 - replaced camshaft position sensor - still getting p0340 - checked wiring connector there is 5 volts on the connector - still getting p0340 and won't start. any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 40,764 Answers

The ECM is the next thing to check for this problem. You will need to know what voltage should be at the connector to determine the fault is in the ECM

Posted on Oct 13, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

  • 323 Answers

SOURCE: getting code P0340, No camshaft position sensor

Replace the cam sensor with a factory sensor. Aftermarket sensors can still trigger the light when nothing is wrong.

Posted on Oct 24, 2009

  • 14036 Answers

SOURCE: 2002 pt cruiser replaced camshaft position sensor

if you replace the crank sensor and camshaft sensor you need a DRB scan tool reprogram sensor to pcm.so they will work.

Posted on Dec 06, 2009

Testimonial: "this did help did not know you need to do this and how do i do this"

Keef2011
  • 160 Answers

SOURCE: 2002 PT Cruiser. Vehicle shut

This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Posted on Mar 06, 2011

  • 170 Answers

SOURCE: I replaced the camshaft position sensor P0340, now the OBD is reading a PO0016

Causes that bring up code P0016 may include:

  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
  2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
  3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.
Hope this helps

Posted on Feb 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTC P0340 other than a defective CPS?


Symptoms can include: Hard starting or no start
Rough running / misfiring Loss of engine power Causes
A code P0340 could mean one or more of the following has happened:
a wire or connector in the circuit could be grounded/shorted/broken the camshaft position sensor may have failed the PCM may have failed
there exists an open circuit
the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code,
diagnosis can be tricky at times. Here are some things to try: Visually inspect all the wiring and connectors in the circuit Check for continuity in the circuit wiring Check the operation (voltage) of the camshaft position sensor Replace the camshaft position sensor as required Check the crankshaft position circuit as well Replace circuit wiring and/or connectors as required Diagnose/replace the PCM as required

Read more at: http://www.obd-codes.com/p0340
Copyright OBD-Codes.com

May 06, 2016 | Nissan Maxima Cars & Trucks

1 Answer

Po340 po344 code has no power and runs rough already changed cam postioning sensor(both) still sending codes had it put on a better computer now is saying there is an electrical problem can't seem to...


checked the spark plug wires if is cracked P0340 is no cam signalat the PCM is. The camshaft position sensor information, along with the crankshaft position sensor information, is used control the fuel injection synchronization. The excess heat from the catalytic converter indicatesunburned fuel going out the exhaust. The catalytic converteris designed to burn any fuelleft in the exhaust. It sounds like your injectors are definitely out of sync dumping raw fuel out the exhaust. Since youreplaced the both the sensors and the PCM, it sounds like a wiring problem betweenone of the sensors and the PCM. Always use a digital multi-meter so you don't blow the PCM. Pull the cam sensor connector and check, with the key on, for about 8VDC on the orange wire (power from the PCM), and put the negative lead on the black/light blue wire (ground.) If you get about 8 volts both of those 2 wires are good. That just leaves thetan/yellow wire (sensor signal.) The signal should fluctuate 0 to 5 volts as the cam notches pass the sensor. To check the wire you would have to probe this wire at the PCM with all the connections put together, key on, and engine rotating (either by hand or with the starter.) The crank sensor wiring could be checked basically the same way. Overheating the cayalytic converter can cause the ceramic beads inside of it to crack, requiring replacement. Don't overheat the converters if you can help it. Turning the key on with a sensor unplugged will usually set an OBD code that will need to be cleared. It sounds like your on the right track. Let us know how it goes. P0340 Camshaft Position (CMP) Sensor Circuit P0344 Camshaft Position Sensor Circuit Intermittent
With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Oct 09, 2011 | Cars & Trucks

2 Answers

I have fault codes P1684 & P0340 on my 2002


P1684 The battery has been disconnected within the last 50 starts.

P0340


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
Symptoms Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

May 30, 2011 | 2002 Chrysler Sebring

2 Answers

I keep getting a code P0340.Chrysler has reprogrammed the PCM for a long start issue.I cant seem to get anywhere with it.


P0340 - Camshaft Position Sensor Circuit Malfunction
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
Hard starting or no start
Rough running / misfiring
Loss of engine power

Causes: A code P0340 could mean one or more of the following has happened:
a wire or connector in the circuit could be grounded/shorted/broken
the camshaft position sensor may have failed
the PCM may have failed
there exists an open circuit
the crankshaft position sensor may have failed

Possible Solutions: With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Visually inspect all the wiring and connectors in the circuit
Check for continuity in the circuit wiring
Check the operation (voltage) of the camshaft position sensor
Replace the camshaft position sensor as required
Check the crankshaft position circuit as well
Replace circuit wiring and/or connectors as required
Diagnose/replace the PCM as required


Hope helps.

Apr 24, 2011 | 2003 Dodge Neon

3 Answers

What does p0340(pd) code mean


P0340 is

Camshaft Position Sensor Circuit Malfunction
What does that mean?

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms

Symptoms can include:

  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes

A code P0340 could mean one or more of the following has happened:

  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Mar 20, 2011 | 1999 Cadillac Seville

1 Answer

2003 sebring 2.4l ck engin light on code po340 can you help


P0340 - Camshaft Position Sensor Circuit Malfunction

This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
* Hard starting or no start
* Rough running / misfiring
* Loss of engine power

Causes: A code P0340 could mean one or more of the following has happened:
* a wire or connector in the circuit could be grounded/shorted/broken
* the camshaft position sensor may have failed
* the PCM may have failed
* there exists an open circuit
* the crankshaft position sensor may have failed

Possible Solutions: With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Visually inspect all the wiring and connectors in the circuit
* Check for continuity in the circuit wiring
* Check the operation (voltage) of the camshaft position sensor
* Replace the camshaft position sensor as required
* Check the crankshaft position circuit as well
* Replace circuit wiring and/or connectors as required
* Diagnose/replace the PCM as required


Test it and keep us updated.

Mar 11, 2011 | 2004 Chrysler Sebring

3 Answers

P0340 code. I Changed cam sensor and checked wiring. what else could be wrong? Jeep cherokee, 6 cil


A code P0340 could mean one or more of the following has happened:

•a wire or connector in the circuit could be grounded/shorted/broken
•the camshaft position sensor may have failed
•the PCM may have failed
•there exists an open circuit
•the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

•Visually inspect all the wiring and connectors in the circuit
•Check for continuity in the circuit wiring
•Check the operation (voltage) of the camshaft position sensor
•Replace the camshaft position sensor as required
•Check the crankshaft position circuit as well
•Replace circuit wiring and/or connectors as required
•Diagnose/replace the PCM as required

Feb 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

My 2004 dodge neon sxt is giving me a p0340 code how do i fix this


A code P0340 could mean one or more of the following has happened:

  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Hope this is for any assistance.

Dec 13, 2009 | 2004 Dodge Neon

1 Answer

Code p0340 need location on 2004 sebring 2.7 v6



P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction


What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

Oct 23, 2009 | 2004 Chrysler Sebring

1 Answer

P0340 code


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM.

A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • a crankshaft position sensor may have failed
With a P0340 Code diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
The location of these 2 sensors vary. Usually they can be found on the back of the engine or on the transmission. I hope this gives you some direction. Thanks for using FixYa!

Sincerely,

JC

Nov 21, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...