Question about Jeep Cherokee

1 Answer

Head bolts

What size are the head bolts on a 2001 jeep cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Jeep Expert
  • 652 Answers

Try a 15 mm socket

Posted on Nov 22, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: tire size for jeep grand cherokee

Should be 235/60/15 You can Actually get the BF Goodrich All Terrain T/A to fit on this Jeep with no Prob. LOTS More Meat and Better Handling and 4x4 Actions

Posted on Jan 03, 2009

  • 512 Answers

SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

  • 1 Answer

SOURCE: window motor replace 2001 jeep grand cherokee

You need to remove all the skrews from the door. Normaly there is one in the handle of the door, one behind the in door lach handel and one under the bump out for the arm rest on the door. Than you need to take a flat head skrew driver slowly priying the panel off. There are plastic clips on the backside of the panel it is ok if you brake a few.

Posted on May 01, 2009

  • 202 Answers

SOURCE: I have a 2001 jeep grand cherokee losing antifreeze no leaks.

good point there is a good chance this has a cracked head

Posted on Nov 17, 2009

  • 740 Answers

SOURCE: When replacing the radiator in a 2001 cherokee jeep sport

i don'nt think there is but if there is they are on the sides of the radiator

Posted on Jan 06, 2010

Testimonial: "Thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I need a special wrench to remove the radiator bracket on a 2001 Jeep Wrangler?


You may have torx head screws there, like on a '95 cherokee: size t-30 for the radiator bracket, and oddly enough, the hood latch piece there was also torx head, but sized t-27.

Jun 10, 2012 | 2001 Jeep Wrangler

1 Answer

Rear caliper bolt size 2001 jeep grand cherokee laredo


If you mean to remove bolt, they are a metric allen size. To replace, you need a special pin / sleeve type bolt, available in sets at the auto parts store for around $14.

Jun 19, 2011 | 2001 Jeep Grand Cherokee

1 Answer

On my 2001 Jeep Cherokee Sport there is water leaking from the top of the engine next to the fire wall. Leak is below valve cover. Is this a Cracked maifoil?


there is a freeze plug back of the head that could be it.or leaking head gasket or the studs or bolts that hold the manifolds on may go into coolant passage. just remove stud or bolt and applie sealant to the threads and reinstall

Apr 04, 2010 | 2001 Jeep Cherokee

1 Answer

What is the cylinder head torque on a 2001 jeep cherokee


Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Mar 06, 2010 | 2001 Jeep Cherokee

1 Answer

How to replace head light bulb in 2001 grand cherokee?


Pop the hood and look at the top of the headlight capsule. you should see a single 7mm bolt somewhere in the middle. remove the bolt completely it should be about 6 inches long. once the bolt is removed then use a large flat screwdriver and carefully pry the headlight capsule out from it retaing clips. once the capsule is out then you have 100% access to the bulbs

Jan 14, 2009 | 2001 Jeep Grand Cherokee

1 Answer

2001 jeep grand cherokee seat removal


i actually removed my 2 front seats very easily as a novice. There really is only i think 4 bolts that need to come out 2 in front and 2 in back. If i can remember correctly i believe it was a larger metric size. Although i dont have power seats, if you do just look for the clip connector and disengage

Jul 05, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...