Ignition key programming

Hi Adriel, The links below are YouTube videos showing how to fix a car that doesn't start/cranks but doesn't start, Also there's videos down the right side of the links that may help as well....................CHEERS..
Fixing Car That Does Nothing When You Turn The Key

Fixing Car That Cranks But Doesn Start Up

Car Cranks But Will Not Start

Auto Repair : Power Door Lock Troubleshooting

sofia2013.com/auto-repair-power-door-lock-troubleshooting/

Jul 29, 2014 - can't use the key i have to go through the passenger door and unlock it ... when I get out of my 2003 Honda Accord, and leave the keys in the ignition, ... Any ideas why all the doors wont lock even pushing the lock button in the

Remote won't unlock passenger or rear doors - TDIClub Forums

https://forums.tdiclub.com/showthread.php?t=355194

Jun 4, 2014 - Will unlock the drivers side door and rear hatch (wagon). ... Any ideas, ... I have the VCDS and tried to program the remote with no success. ... precisely, but it was something like put the key in ignition, turn to acc, then push the unlock button. .... fiddling around with passenger door did not produce any result.

Door locked with key in ignition - TDIClub Forums

https://forums.tdiclub.com/showthread.php?t=125387

Dec 17, 2005 - Anybody have any ideas on this? I know there should ... The door willlock with the key in the ignition and the car running. It does automatically ...

Ignition key won't open door - 8th Generation Honda Civic Forum

www.8thcivic.com > ... > Mechanical Problems & Technical Chat

1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition and Pull key out twice (Do NOT Turn)


3. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into ignition and leave it in ignition.
C. Close the drivers door.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

Hi. I have a 2005 suzuki Swif, it has a yellow lock light on the dash which has just appeared and my car will not start?? do you have any idea what may bbe wrong??

hi well this is a bit long so if you can bare with me i will try explain how to , clear system to decode, and recode as this is what it sounds like that the coding has gone from the ignition key....ok here goe's
to sync key with car depress lock or unlock button manually lock the drivers door within 30 seconds of the above system should now work....if not do next bit
switch ignition on ( using non chip key ) manually lock drivers door using key ( another one, hopefully you will have more than one) press unlock button 5 times, in one second intervals indicators flash 5x for every time signal is received switch ignition off and remove key
that's the de-programming done...
to de-program the system if above fails..........
switch ignition on ( use key without remote ) manually lock drivers door using key to be synced with car complete the following within 30 seconds of doing above within 5 seconds press the unlock button on key indicators should flash once wait 5 seconds press unlock button once to confirm programming vehicle should unlock this also will confirm deactivation of programming mode switch ignition off remove key..that should be it, then try new programed key in ignition.

to re-program system and sync with key switch ignition on manually lock drivers door using key ( another one, hopefully you will have more than one) press unlock button 5 times, in one second intervals indicators flash 5x for every time signal is received switch ignition off and remove key
that should be it, if no joy then will have to main dealer i am afraid...hope this helps

hi i have had the same problem, the things is your key has lost its coding to your car, is it the diamond shpe key with a open, lock and open boot on it if it is you can get in your car turn the ignition to the point before the engine starts,
take the key back out,
hold the unlock button,
whilst holding the unlock button press the lock button three times,
let go off all buttons then the locks should bounce to say the car key has recoded its self,

hope this helps cheers

Don't buy it from the dealer, just buy a used remote from eBay. Use these instructions to program it.

1. Confirm that all doors are closed and the ignition key is out of the ignition cylinder.
2. Open the driver's door.
3. Within 10 seconds, Insert key into ignition turn to ON position and back to OFF and remove the key.
4. Within 20 seconds, close and open the drivers door 3 times. (Drivers door should be open)
5. Within 10 seconds, insert key into ignition turn to ON position and back to OFF and remove the key.
6. Press and hold both the LOCK and UNLOCK buttons together on the same remote for at least 5 seconds, the doors will lock and unlock (that's a very good sign)
7. Within 5 seconds, press the LOCK button on the same remote and release. You just programmed your remote ??

Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entry, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 40 seconds)
  
  1. Insert the key into and remove it from the ignition switch 2 times.
     (IN - OUT - IN - OUT)
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Insert the key into and remove it from the ignition switch 1 time.
     (IN - OUT)
     
  4. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  5. Insert the key into the ignition switch and leave it in.
     
  6. Close the driver's door.
     
  7. Turn the key from LOCK to ON 4 times, ending at LOCK
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
     
  8. Wait for the locks to stop, then remove the key from the ignition switch.
     
• On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
  
  1. [For all doors unlock] press and release the UNLOCK button.
     
  2. [For driver door unlock] press and release the LOCK button.
     
• Open the driver's door. The programming is complete. If programming did not occur, start over.

Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode