Question about Chrysler Concorde

Open Question

1997 Chrysler Concorde

How much does it cost to replace the motor mounts on a 1997 Chrysler Concorde.

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

csmock132
  • 4669 Answers

SOURCE: replace the engine motor mounts and the transmission mount. Would like to know how to do it. Thanks.

Check the frame mounts too. You will have to loosen the bolts and jack the motor up with a jack and a woodblock.

Posted on May 04, 2009

ZJLimited
  • 17970 Answers

SOURCE: how do you replace the egr valve in a 1997

Chrysler Concorde 1993-1997 3.5L MFI 6cyl
Exhaust Gas Recirculation System
Operation

This system reduces the amount of oxides of nitrogen (NO x ) in the exhaust by allowing a predetermined amount of exhaust gases to recirculate and dilute the incoming fuel/air mixture. The diluted air/fuel mixture reduces peak flame temperature during combustion, which in turn inhibits the production of Nitrogen oxides. The principal components of the system are:
- EGR tube (connects a passage in the intake manifold to the exhaust manifold)
- EGR valve
- Electronic EGR Transducer
- Vacuum hoses


Component and System Testing

  1. Check the condition of all of the EGR system hoses and tubes for leaks, hardening or kinks on the rubber hoses. Repair and correct these conditions before proceeding any testing.
  2. Be sure that the hoses at both of the EGR valve and EGR valve control are connected to the proper fittings.
  3. Be sure the electrical connector is firmly attached at the valve control.
  4. To check the EGR system operation, connect the DRB III scan tool or equivalent to the 16-way data link connector. The data link connector is located on the lower edge of the instrument panel near the steering column. Follow the scan tool instructions.
  5. After checking the system with the DRB III scan tool, proceed to the EGR valve leak and control tests, then repair as necessary.

Removal & Installation
EGR Valve and Transducer

395f8b9.jpg

EGR valve and transducer assembly-3.5 engine



025dc6c.jpg

The EGR valve attaches to the back of the cylinder head-3.5L engine


bc80254.jpg

Loosen, but do not remove, the EGR tube to intake manifold screws

The EGR valve attaches to the rear of the right cylinder head.
  1. Remove the vacuum tube from the electric EGR transducer solenoid. Inspect the vacuum lines for cracking, poor seal due to hardness, or other problems. Replace with new hoses if necessary.
  2. Remove the electrical connector from the solenoid.
  3. Slide the transducer up and out of the mounting bracket.
  4. Loosen, but do not remove, the EGR tube to the intake manifold screws.
  5. Remove the EGR tube lower screws at the valve.
  6. Remove the EGR valve and transducer.
  7. Clean both gasket surfaces and check for any signs of leakage or cracks. Replace the components if any such damage is found or if the valve fails the tests.

To install:
  1. Loosely install the EGR valve and a new gasket onto the cylinder head.
  2. Using a new gasket, attach the EGR tube to the valve and tighten the screws to 95 inch lbs. (11 Nm).
  3. Tighten the EGR tube to the intake manifold plenum screws to 16 ft. lbs. (22 Nm).
  4. Tighten the EGR valve to the cylinder head screws to 16 ft. lbs. (22 Nm).
  5. Reconnect the transducer solenoid to the vacuum fitting on the manifold.
  6. Slide the transducer into the bracket.
  7. Reconnect the vacuum lines and electrical wires to the EGR transducer.
continue...

Posted on Sep 04, 2009

bschilz
  • 2049 Answers

SOURCE: how do i replace the water pump on a 1997

First, keep a copy of this serpentine belt diagram to help you put it back on when you're done replacing the water pump...

b98fcba.jpg
Here's a link to a video by Advance Auto Parts on how to replace the water pump...
http://www.wonderhowto.com/how-to/video/how-to-replace-a-water-pump-in-a-vehicle-102464/

Posted on Jan 28, 2010

  • 34 Answers

SOURCE: 1997 Chrysler Concorde LXI. Radio works its just

Try disconnecting the battery for five minutes and then reconnect. This may reset the memory in the radio.

Posted on Sep 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do the motor mounts leak on a 1997 chrysler concorde 3.5


motor mounts are rubber and do not use fluid. If they are wet then you most likely have an oil leak

Sep 02, 2015 | Chrysler Cars & Trucks

1 Answer

Wher are the motor mounts


the engine has two mounts, the trans has one.

engine mounts are located on the left and right of the engine slightly forward of center. on the bottom, they have studs that go through holes in the cradle - two for each mount. on the top, each has two more studs that engage brackets on the engine. each is covered by a thin metal heat shield (which makes them hard to see by a casual observer).

the trans mount is at the back of the transmission and secures it to the crossmember.

May 30, 2014 | 1997 Chrysler Concorde

1 Answer

Where are the motor mounts


the engine has two mounts, the trans has one.

engine mounts are located on the left and right of the engine slightly forward of center. on the bottom, they have studs that go through holes in the cradle - two for each mount. on the top, each has two more studs that engage brackets on the engine. each is covered by a thin metal heat shield (which makes them hard to see by a casual observer).

the trans mount is at the back of the transmission and secures it to the crossmember.

May 30, 2014 | 1997 Chrysler Concorde

2 Answers

How do change serpentine, and ac belt on 3.2 ,2001 chrysler concorde. do i loosen nut on tension pully. It is really tight. then how does it looosen to remove belt


Beside the pulley on the arm it is mounted on is a square hole. Place a 1/2 drive breaker bar in that hole and push to right or left. One way will looken the belt. It is a very heavy spring so don't do it till you have the belt to replace with.

May 28, 2011 | 1999 Chrysler Concorde

1 Answer

1997 Chrysler Concorde LXI. Radio works its just


Try disconnecting the battery for five minutes and then reconnect. This may reset the memory in the radio.

Sep 16, 2010 | 1997 Chrysler Concorde

1 Answer

Adding oil


Hi!!

If you look closely, you'll see that the "plastic insert" is not going to block the passage of oil, so, add as much motor oil as needed, the recommended is 20W50.

Don't forget to rate this post. Good Luck!

Apr 30, 2010 | 1997 Chrysler Concorde

1 Answer

I cant get the starter out


You have to remove left motor mount.

Feb 22, 2010 | 1998 Chrysler Concorde

1 Answer

Need diagrahms to replace and install internal water pump for a 1997 Chrysler Concorde.


Your best bet would be to get the Haynes or Chilton repair manual from the local auto parts store for your vehicle. It should cost about $20.00.

Dec 18, 2009 | 1997 Chrysler Concorde

1 Answer

Replace the engine motor mounts and the transmission mount. Would like to know how to do it. Thanks.


Check the frame mounts too. You will have to loosen the bolts and jack the motor up with a jack and a woodblock.

May 04, 2009 | 1996 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...