Question about 2001 Toyota Camry Solara
My 2000 toyota solara gas gage didnt move
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Either fuel sensor is bad or coated with sulfur residue from inferior gas. Try a can of Sea Foam gas treatment OR can of Techuron concentrate. Both available at auto parts and , of course, Walmart ! Add to full gas tank, drive 75 - 100 miles and see if all is well. If not, condide4 sensor change
Posted on Dec 09, 2008
the other areas the fault could be located are in your meter circuit plate (which is part of your combination meter), it could be in the wiring, or possibly your multi display (also part of your combination meter)
Posted on Mar 15, 2009
check the fuses in your manual it will tell you which fuses are for the dash and replace them it sounds to me like they are blown! good luck
Posted on Jan 09, 2010
It easy ! You need a philips and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.
Next lift the plastic cover and remove the six gold bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Posted on Apr 22, 2010
Tips for a great answer:
Apr 14, 2013 | 2000 Pontiac Montana
Apr 14, 2013 | 2000 Pontiac Montana
Jul 13, 2012 | 2005 Pontiac Montana
Apr 25, 2012 | Cars & Trucks
Jun 17, 2010 | 2000 Buick LeSabre
Mar 16, 2010 | 2004 Pontiac Montana
Sep 05, 2009 | 1997 Toyota Land Cruiser
Aug 08, 2009 | 2000 Ford Taurus
May 04, 2009 | 2000 Pontiac Montana
Dec 23, 2008 | 2003 Pontiac Montana
74 people viewed this question
Usually answered in minutes!