Question about Ford Explorer

1 Answer

Where is the camshaft sensor on a 1998 ford explroer located

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

The cam shaft sensor should be located on the front of the drivers side of the engine head just below the valve cover.. might be a bracket hiding it but it should be their look for a wiring going to the front of that left side front head.... hope it helps

Posted on Oct 13, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

csmock132
  • 4669 Answers

SOURCE: Crank sensor and camshaft sensor

The crank sensor is in the top of bell housing of the transmission towards the back of the engine compartment. The cam sensor is built into the distributor.

Posted on Mar 07, 2009

savdragon
  • 37 Answers

SOURCE: locate camshaft sensor 2002 chevy trailblazer

Assuming you have a 4.2L engine here is the location.
b3031ef.gif

Hope this helps out,
if so please rate my answers.
Brett

Posted on Mar 19, 2009

emissionwiz
  • 75005 Answers

SOURCE: camshaft position sensor location

At the right rear of the engine under the intake manifold and to the left of the oil filter. You will probably need to go under the car to spot it, it's the sensor with a three-wire connector arranged vertically. But you can take it out from above. It's held in with a single bolt with an eight MM head located just above the sensor. Un-clip and remove the electrical connector. Unscrew the bolt with a socket wrench & extension bar. Wiggle and pull the sensor out.
here is a picture.
255f615.jpg

Posted on Apr 10, 2009

blueextc3221
  • 15935 Answers

SOURCE: o2 sensor location

DTC P0156 indicates the output voltage of the downstream Heated Oxygen Sensor (HO2S) is less than some calibratable functional window. The possible causes are:

  1. Pinched, shorted and/or corroded wiring and pins.
  2. Crossed sensor wires
  3. Exhaust leaks.
  4. Contaminated HO2S.
  5. Bad HO2S.
Since you didnt specify the engine size in your vehicle - please see the diagram below for the location of the sensor(s)

84f80ca.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Apr 16, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

Where is the camshaft position sensor on a 1998 Dodge Dakota 5.2L


The camshaft position sensor is located on the distributor for all engines designed for the 1998 Dodge Dakota. Accessing the sensor requires removing the distributor cap and the distributor rotor. The camshaft sensor pigtail comes through the front of the distributor and connects to the engine wiring harness above the intake manifold.

Oct 03, 2012 | Cars & Trucks

1 Answer

1998 ford explorer speed senser cam-shaft pulley WERE IS IT LOCATED


Sorry you said camshaft sensor look behind the intake manifold back next to the firewall the sensor should be their but, i don't no about a pulley but there is a camshaft synchronizer beneath the sensor itself.

May 11, 2011 | 1998 Ford Explorer

1 Answer

I have a 1998 Ford Explorer V6 4.0L I am trying to find out were my Camshaft Position Sensor is located and can i get to it without having to remove any other parts such as air intake lines or anything...


It should be on the drivers side valve cover directly to the rear of the the oil fill cap, should have one bolt that holds it in place with two wire connector on it.

Apr 26, 2011 | 1998 Ford Explorer

2 Answers

1998 Ford Ranger 4.0 engine Engine will not start Code is Camshaft position sensor. Where is this located


It is behind the intake manifold in the center of the block, on the rear of the engine.

Jan 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

Were is the camshaft position sensor located on a 1998 ford escort


normally its the engine head, most likely its in the other side of the head to the timing belt. it will have two wires coming out of it and held in by two screws.

Nov 27, 2010 | 1998 Ford Escort

1 Answer

I nee instructions on a cam sensor removal for a 1998 ford contor with a 16 vale 2.o over head cam engine


The camshaft sensor is located at the back of the head on driver side. Remove the wire,unscrew the sensor,screw the new sensor in the head and put the wire back on the sensor

The camshaft sensor is not in the back on the 98 4 cyl its right in front. All you need to do is take off the 3 bolts on the top of the heat shield and pull it back a bit and it will be right there.

Apr 24, 2010 | 1998 Ford Contour

3 Answers

Where is the Camshaft Position Sensor located on a


this car has but one bank, the cam sensor is under the intake manifiold on the drivers side.

Feb 25, 2010 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...