Question about Cars & Trucks

1 Answer

How do you read codes on a 91 dodge ram charger there is no ob2 plug in?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,337 Answers

Data Link Connector

The data link connector is a dedicated diagnostic scan tool connector. It is located in the engine compartment against the fire wall. It links the engine controller to the Diagnostic Readout Box (DRBII) scan tool or the Mopar Diagnostic System (MDS), or any other Chrysler-compatible diagnostic scan tool.
Here's a link to the codes.Tyler,join the at top right corner,it's free,then you can use there repair guides like me.

Posted on Oct 12, 2013

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 234 Answers

SOURCE: hello i have a problem on

You may want to have a compression check performed, chances are you may have a burnt valve. you did not cross the wires on 2 and 3 maybe?

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

91 dodge ram charger wires on drivers side burnt were do i start car shut down

fusible links are short bits of fuse and can be easily replaced
it should have burnt before the harness was damaged
they are available at the spares section

Oct 22, 2015 | Dodge Cars & Trucks

1 Answer

91 Dodge Ram power50. Changed spark plug and wires, fuel filter, had coil checked by a mechanic. It was good. Still I have no spark. Please help!

check tke ignition control module
check for immobilizer operation
run the fault codes to check for cam/crank position sensor faults

Sep 06, 2015 | Dodge Cars & Trucks

1 Answer

My dodge ram 2500 pick up slip transmission how to fix 2006

First have the codes read, while you can still drive it. With a scanner, not a code reader. Readers don't read transmission codes. It could be something cheaper, like a solenoid replacement. Or a costlier transmission rebuild.

Apr 13, 2014 | 2006 Dodge Ram 2500

1 Answer

How to read the code on an 87 dodge ram 50

On full size Dodge trucks, you cycle the key switch to make the light flash.
On Dodge imports such as the D-50 truck, you have to use a test meter and connect it to a plug under the radio.
You can find the procedures and trouble codes in a repair book or by researching it online.

Feb 25, 2013 | 1992 Dodge Ram 250

1 Answer

New plug misfire in dodge ram 1500 6 cyl van

could be your coil, but can also be internal, have you replaced both the air & fuel filters ? if so, dump some good fuel injector cleaner into tank when half empty , top off with 91-92 octane fuel, see how that works for you, do some highway driving, stop & go traffic creates problems, todays fuel w/ethonal is bad for older cars, be sure to have code cleared from ecm !

Feb 15, 2013 | 1999 Dodge Ram

1 Answer

What is 02S not ready meam on a ob2 scan

O2 is oxygen and s is sensor. The O2 sensors are probably not warmed up yet.

Dec 17, 2012 | 2000 Dodge Caravan

1 Answer

While im driving to work lights just pop out in my dash board i just got new spark plug and did transmession fluids. and while im driving up the hill, ive notice that its got hardto go up.

have codes pulled for free from auto parts store they will tell you what codes mean they have a ob2 they plug it into your harness tells them why the lights on dash are comeing on then you can fix it need any more help just respond back to me

Dec 11, 2010 | 2000 Dodge Durango

1 Answer

Hello i have a problem on my neon 2000 it s read on ob2 code 302 and 303 witch say misfired 2,3 cylinder i change plugs and coil pack still read the same thank

You may want to have a compression check performed, chances are you may have a burnt valve. you did not cross the wires on 2 and 3 maybe?

Aug 15, 2009 | 2000 Dodge Neon

1 Answer

Need fuse box diagram for 91 dodge ram 150 van

i have the diagram for dodge ram van 250. don't know if it's the same, but i have it. find me at

Mar 09, 2009 | 1991 Dodge Ram 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides