Question about Cars & Trucks

Open Question

Torque settings dual mass flywheel vw passat - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

Ad
TDISLine
  • 1874 Answers

SOURCE: flywheel torque setting vw transporter t30

VW Transporter 2.5 TDI-PD, (made year: 2003 ... 2007), engine code: AXD, 130 HP / 3500 rpm.
Important note: use new bolts!
Flywheel/driveplate torque setting: 60 Nm + 90 degrees.
Clutch to flywheel torque setting: 22 Nm.

Posted on May 21, 2010

alicantecoli
  • 22326 Answers

SOURCE: does a 2001 2.5 subaru

honestly dont know offhand but what i do with some of these vehicles that do have one is when changing a clutch i weld the thing together so they dont give future problems

Posted on Sep 17, 2010

  • 5 Answers

SOURCE: good day, i need to

Hi rita d ,
the answer to your question according to information supplied by auto data ( the bible to us techs) is 60Nm, then a further 90 degrees. You should also use new bolts. Hope this helps,
Doc Scott

Posted on Jun 22, 2011

  • 16 Answers

SOURCE: dual mass flywheels

for light vehicle, recommended torque is 45 newton meter and an additional 3/4 turn of the wrench and for 6 bolts tightening sequence should be 3 by 3 as star delta.

Posted on Feb 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i check for the timing marks on the automatic flywheel for the vw passat v6 amx engine


Hi. The amx does not ahve a flywheel pick up. the crank sensor g28 is on the side of the block. The flywheel have offset bolts so can only be fitted in the correct position. The best way to set tdc is with a special tool that goes into the side of the block at g28 sensors hole, or to set tdc with a dial gauge on cylinder 1. I don't yhink the flywheel fitment is the issue with this vehicle. Have you disconnected the air mass meter and run the car to see if it is beter? The air mass meter commonly fails when disturbed during repairs.

Jan 15, 2014 | Volkswagen Passat Cars & Trucks

1 Answer

Dual mass flywheels


for light vehicle, recommended torque is 45 newton meter and an additional 3/4 turn of the wrench and for 6 bolts tightening sequence should be 3 by 3 as star delta.

Feb 22, 2012 | 2005 Renault Laguna II

1 Answer

My 2005 golf 5 gti dsg currently has 89000km on the clock. It is used extensively in traffic covering 60km/day/week. It has developed an irritating "knocking noise" in the engine.Booked it at a local VW...


hi,
i couldn't say for certain without hearing the noise , but i have replaced one or two "dual mass flywheels" on these models, alot of people don't realise the dsg actually has a dual mass flywheel.
regards
P

Aug 03, 2010 | 2008 Volkswagen Gti

1 Answer

Does Volkswagon cover flywheel under manufacturing faults -


dual mass flywheels are prone to wear, would only be covered under manufacturers limited warranty when vehicle was sold new

Jun 12, 2010 | 2006 Volkswagen Passat

1 Answer

Flywheel torque setting vw transporter t30


VW Transporter 2.5 TDI-PD, (made year: 2003 ... 2007), engine code: AXD, 130 HP / 3500 rpm.
Important note: use new bolts!
Flywheel/driveplate torque setting: 60 Nm + 90 degrees.
Clutch to flywheel torque setting: 22 Nm.

May 21, 2010 | 2004 Volkswagen Eurovan

1 Answer

Grinding in tranny after replacing clutch


Did you remember to torque all of your clutch plate bolts? Flywheel bolts?

May 04, 2010 | 1996 Ford F250 Crew Cab

2 Answers

96 FORD F-350 7.3 TURBO DIESEL 5 SPEED


no, it shouldnt have any looseness to it and dual mass flywheels are VERY expensive to replace, BUT yes it can be converted to a solid flywheel, check out autozone.com part number MU1989 or advanceautoparts.com part number 798, that should get you on the right path to curing your problems, i welded the two independantly turning discs of my dual mass flywheel together but i wouldnt recommend anyone doing that without the proper equipment to do so (i.e. precision lathes, cast iron welding rods, etc)

Mar 29, 2009 | 1996 Ford F350 Crew Cab

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper


diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Jan 03, 2009 | 2001 Isuzu Trooper

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...