Question about 1997 Chrysler Sebring

Open Question

Location of crankshaft position sensor on 2007 Chrysler Sebring with 2.4 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: camshaft position sensor

This V-6 has a very hard to find/hard to reach CKP - it is directly under the Distributor, about 4 inches below, inwards toward the Transaxle "bell". Almost dead-center in the back of the engine.
Your going to have to take the Air Filter and the air manifold that runs to the engine off. After that, take off the horn assembly to gain very, very limited access to wedge an extended ratchet into the bowels of the engine. 
I think the same socket that undid the horn assembly fit the CKP nut. It takes 10 minutes to undo the bolt a couple ratchet clicks at a time, at least 15 to get the thing to wiggle out, probably 15 minutes to unconnect, reconnect, and snap back to the fram the wire harness, and at least another 10 minutes to ratchet the bolt back in click by click.

Now you know why they say shops charge $500 in to do this - I think they must take the entire engine out... Very painstaking job that requires patience and precision... but quite satisfying to finish it yourself. 

Good luck and hope this helps, 

Posted on Apr 23, 2009

Ad
  • 1 Answer

SOURCE: Where is the crankshaft position sensor located?

the crankshaft position senor on the 2.2L is located on the rear right side of the engine block

Posted on Jul 07, 2009

co7196
  • 3433 Answers

SOURCE: need location of crankshaft position sensor on a

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

johnjohn2
  • 5763 Answers

SOURCE: location of crankshaft sensor chrysler

Heres adiagram to help you, its located at right rear of motor.15663b6.gif

Posted on Oct 18, 2010

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the location of the cam position sensor in a 2007 chrysler sebring 2.4 engine?


Usually the crank shaft position sensor is located on the top of the transmission bell housing, on the back side right next to the top of the motor. Do you have a trouble code?

Jun 23, 2016 | 2007 Chrysler Sebring Sedan

2 Answers

WHERE ARE THE CAMSHAFT POSITIONING SENSOR(S) ON A 07 SEBRING 2.4?


On the 2.4l there are two cam sensors. They are located on both sides, rear of the engine, just under the valve/rocker arm covers. They are bolted on with one 10mm bolt.

Jan 31, 2012 | 2007 Chrysler Sebring 2.4

1 Answer

Sebring 1997 I need picture to lookat the PCM sensor and the Crankshaft position sensor (CKP sensor)


On 1997 Chrysler Sebring 2.5L MFI 6cyl...
- the PCM is located in the left side of the engine compartment, beside the Power Distribution Center (PDC).

zjlimited_767.gif

Fig. 1: Location of the PCM on the Cirrus, Stratus, Sebring convertible and Breeze models

zjlimited_768.gif

Fig. 2: Location of the PCM on the Sebring coupe and Avenger models

- the Crankshaft Position Sensor is located: under hood, driver side, upper engine area, mounted on end of engine block

zjlimited_769.gif

Fig. 4: Location of the crankshaft position sensor on 2.5L engines

Hope helps; remember to rating this answer and leave some testimonial comments.

Oct 09, 2011 | 1997 Chrysler Sebring

2 Answers

Where is the crankshaft sensor located on a 2005 Chrysler Sebring


It is located under the starter that is for a 4 cylinder engine if you are a six cylinder or 2.7 it is located on the rear of the transmission housing above the differential housing

Aug 05, 2011 | 2005 Chrysler Sebring Conv

1 Answer

No fire at distributor


The 1997 Chrysler Sebring 2.5L has a distributer with an intergrated coil. All other models have a distributerless ignition ("coil packs").

Start by testing the ASD (Automatic Shut Down) relay, then the CPS (Crankshaft Position Sensor) and CMH (Camshaft Position Sensor).

The CMH test the same way likethe CPS; the ASD is located on cowl, at left rear of engine compartment.

Hope helps.

Jul 28, 2010 | 1997 Chrysler Sebring

1 Answer

Where is the crankshaft position sensor located on a 2000 Sebring Conv.


removal steps (CPS) -remove air intake hose -Battery tray -Crankshaft position sensor

Apr 27, 2010 | 2000 Chrysler Sebring

1 Answer

How can i replace the crankshaft position sensor on a 1999 sebring lxi


Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Jun 25, 2009 | 1999 Chrysler Sebring

1 Answer

Where is the crankshaft position sensor located? On a 2004 Chrysler Sebring 2.2L


the crankshaft position senor on the 2.2L is located on the rear right side of the engine block

Jun 13, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
1997 Chrysler Sebring Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...