Marcy multi gym upper cable replacement can you help

double posted, with 1999 added.
the FSM says dont reuse steering wheel bolts.. (unique)
here is an online quote to get to the combo switch
quote;
Removal & Installation

1. Disconnect and isolate the battery negative cable. WARNING(bags can kill, my comment)
   Wait two minutes for the airbag system reserve capacitor to discharge before performing further diagnosis or service.
2. From below the steering column, remove the three screws that secure the lower steering column shroud to the multi-function switch mounting housing.
3. Using hand pressure, push gently inward on both sides of the upper shroud near the parting line between the upper and lower shrouds to release the snap features that secure the two shroud halves together.
4. Remove both the upper and lower shrouds from the steering column.
5. Remove the Steering Control Module (SCM) from the steering column.
6. Remove the two screws that secure the left multifunction switch to the SCM .
7. Disengage the two retaining tabs , next to the screw mounts that secure the left multi-function switch to the SCM.
8. Disconnect the left multi-function switch from the SCM.

To install:

1. Position the left multi-function switch onto position on the Steering Control Module (SCM) .
2. Engage the two retaining tabs, next to the screw mounts that secure the left multi-function switch and firmly snap into place.
3. Install the two screws that secure the left multifunction switch to the SCM. Tighten the screws to 22 inch lbs. (2.5 Nm).
4. Position the lower steering column shroud to the underside of the steering column.
5. Install the three screws that secure the lower steering column shroud to the multi-function switch mounting housing. Tighten the screws to 17 inch lbs. (2 Nm).
6. Position the upper column shroud over the steering column with the hazard warning switch button inserted through the hole in the upper shroud.
7. Align the snap features on the upper and lower shrouds and apply hand pressure to snap them together.
8. Reconnect the battery negative cable.

Not a car question, but you will probably need to contact the company.

Ensure lever is in center of off position.Disconnect negative battery cable. Disable airbag system. Remove steering wheel. Remove lower and upper column covers. Remove lock cylinder if necessary. Remove wiring harness strap. disconnect steering column electrical connectors. Disconnect turn-signal and multi-function switch Gray and Black connectors. Remove turn-signal and multi-function switch from vehicle.

There are just (3) possible reasons for this:
(a) your headlight switch has failed, or
(b) your headlight relay has failed.
(c) Fuse 1 (25 Amps) has blown

The headlight relay and fuse 1 are located (I think) in a fuse/relay block under the hood.
The headlight switch is part of the "Multi-function Switch" on the steering column.

Here's how to replace the 2001 PT Cruiser multi-function switch:


Multi-Function Switch Removal & Installation
1. Open the hood.
2. Disconnect and isolate the battery negative cable.
3. Remove both upper and lower steering column shrouds.
4. Disconnect both posi-lock harness connectors at the rear of the multi-function switch.
5. Remove multi-function switch mounting screws and remove switch from vehicle.




To Install the new multi-function switch:

Note:
If replacing the multi-function switch, the combination flasher and windshield wiper/washer switch
must be transferred to the new multi-function switch.

1. Remove the two Torx(R) screws retaining the wiper/washer switch, place next to the new
multi-function switch and install two screws.
2. Place switch into place and install mounting screws. Torque multi-function switch to column
retaining screws to 27 inch-lbs. (3 Nm).
3. Connect both posi-lock harness connectors at the rear of the multi-function switch.
4. Install both upper and lower steering column shrouds.
5. Connect the battery negative cable.
6. Close hood.
7. Verify vehicle and system operation.

Multifunction Switch -I suspect this switch or the connection at the harness is bad or contaminated. Removal & Installation To Remove:

1. Disconnect and isolate the negative battery cable.
2. Remove the upper and lower steering column shrouds.
3. Disconnect wire connector from the back of the multifunction switch.
4. Remove screws holding multi-function switch to steering column adapter collar.
5. Remove the multi-function switch.

To Install:

1. Position the switch on to the steering column and install the mounting screws.
2. Connect the electrical connectors to the switch.
3. Install the upper and lower steering column shrouds.
4. Connect the negative battery cable.

Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)



Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column

1. Disconnect the negative battery cable.
2. Remove the upper and lower steering column shrouds.
3. Pull the flasher from the back of the multi-function switch.
   

To install:

1. Install a new flasher in the multi-function switch.
2. Install the column shrouds.
3. Connect the negative battery cable.

Hazard Warning Flasher

1. Disconnect the negative battery cable.
2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:

1. Install a new flasher in the connector.
2. Install the knee bolster panel.
3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Kia_Sephia_Rio_Spectra_Optima_1998-2006
Multi-Function Switch - Removal & Installation

1. Disconnect the negative battery cable.
2. Remove the steering wheel, as outlined earlier in this section.
3. Remove the steering column upper and lower shrouds.
   
   
   Fig. Remove the steering column upper (A) and lower shrouds (B)
   
4. Detach the multi-function switch electrical connector(s).
   
   
   Fig. Detach the multi-function switch (A) electrical connector(s)
   
5. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B).
6. Installation is the reverse of the removal procedure.
   
   
   Fig. Remove the 3 bolts, as shown, then remove the multi-function switch assembly (B)
   

Hope this help (remember rated this post).

1. Remove the negative battery cable.
2. If you have tilt remove the tilt lever.
3. Remove the upper and lower shroud.
4. Remove the lower fixed column shroud.
5. Move the upper shroud enough to access the back of the multi-function switch.
6. Remove the tamper proof Torx screws (Snap on TTXR20B2 bit or equivalent).
7. Gently pull the switch away from the column to access the screw holding the instrument panel wire harness connector to the switch.
8. Disconnect the connector and reverse to install new switch.

• Headlamps Inoperative

• Fuse.
• Headlamp switch.
• Headlamp relay.
• Circuit.
• Bulbs.

Section 11-05: Steering Column Switches 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Multi-Function Switch
Removal

1. WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS.
   Disconnect the battery ground cable (14301) and wait one minute for the backup power supply to be depleted.
   

1. Remove the steering wheel (3600). Refer to Section 11-04 for the removal procedure.
   

1. Remove the four screws from the lower steering column shroud (3530).
   
   
   
   
   

1. Remove the ignition switch lock cylinder illumination lamp socket from the lower steering column shroud.
   

1. Remove the lower steering column shroud.
   

1. Remove the upper steering column shroud.
   

1. Disconnect the three multi-function switch electrical connectors.
   

1. Remove the multi-function switch screws.
   

1. Remove the multi-function switch electrical connectors and the multi-function switch (13K359).
   

I would suggest an internally shorted multifunction switch. It should not be very expensive at a dealer and really easy to replace.
MULTI-FUNCTION SWITCH REMOVAL

1. Disconnect battery negative cable.
2. Remove the upper steering column cover. Refer to steering column cover removal procedures below.
3. Remove multi-function switch mounting screws Multi-Function Switch
4. Disconnect wire connectors. Lift the switch straight up to remove.

INSTALLATION For installation, reverse the above procedures.

1. Tighten multi-function switch to column retaining screws to 2.3 N·m (20 in. lbs.) torque.
2. Tighten steering column cover retaining screws to 2 N·m (17 in. lbs.) torque.