Question about Cars & Trucks

1 Answer

Adjusting the clutch cable on a 1993 isuzu pickup

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 20,706 Answers

How to ?
who can?
what spec play.
who to unfreeze the nuts (adjusters)
post a question like that. how?

Posted on Oct 12, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre

To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Posted on Mar 05, 2009

michigan man
  • 3533 Answers

SOURCE: clutch adjustment on a 1995 isuzu rodeo

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

  • 701 Answers

SOURCE: Where is clutch safety switch located on 1992

Hello mtripp: My name is Roger and I will answer your question. The neutral safety switch is located on a bracket directly above the clutch pedal. Should have two wires that plug into it. One should be white with a blue tracer and the other wire should be black with white tracer. Should you need further help please just ask. Please rate the answer you received as this way i know it was helpful. Thank You for using Fix Ya. Roger

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Isuzu Pickup 2.3L Clutch Problem


Seems like the cable is broken (only a few strands left & stretched). Remove the cable & check it out. Probably needs to be replaced.

Oct 12, 2015 | 1990 Isuzu Pickup

1 Answer

Isuzu clutch adjustment


Questions Answers for clutch adjustment isuzu rodeo
Try this link.

Aug 14, 2014 | 1986 Isuzu Pickup

1 Answer

I have a 93 isuzu pickup and my clutch is slipping from time to time it is cable driven and im trying to figure out how to adjust it and where adjustment is located


I Do Not Think It Is Adjustable, I Would Say That The cable Is now Getting Stuck Inside The Outer Cable Best Is To Fit New cable

Mar 21, 2013 | 1993 Isuzu Pickup

1 Answer

How to adjust the idle screw on a 1993 2.6L isuzu pickup?


it should be run be a sensor idle air control valve

Dec 02, 2012 | Cars & Trucks

1 Answer

How do i tighten my clutch cable on my 1992 isuzu pickup?


If this has the cable clutch then there should be an adjustment nut which is longer than the two nuts on each end. You can place a wrench on the smaller nut on one end and turn adjustment nut to change tension.

Jun 04, 2012 | 1992 Isuzu Pickup

1 Answer

Replacing clutch cable


This model uses an hydraulic clutch and it is self adjusting, a slipping clutch means the clutch pressure plate and disk are worn out.

May 25, 2012 | 1995 Isuzu Pickup

1 Answer

Clutch adjustment for a 1994 isuzu pickup


NO ADJUSTMENT... IT IS A HYDROLIC CLUTCH, MAY NEED TO REPLACE SLAVE CYLINDER OR CLUTCH MASTER CYLINDER.

Jul 09, 2011 | 1994 Isuzu Pickup

1 Answer

I have a 1993 isuzu pick up newly built need schematics on firing order and distributor rotor location and timing marks and timing belt replacement any help will be thankfull


1993 Isuzu Pickup 2WD
2.3 liter SOHC L4

05fbccb.gif
1993 Isuzu Pickup 2WD
2.6 liter SOHC L4 .......same as above


1993 Isuzu Pickup 2WD
3.1 liter V-6

3287635.gif
4wd is the same specs as the 2wd.

Apr 22, 2009 | 1993 Isuzu Pickup

1 Answer

Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre


To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Mar 04, 2009 | 1994 Isuzu Pickup

1 Answer

93 Isuzu Picku clucth cable


You should be able to hook it up yourself. Don't forget to adjust the clutch when you are done.

Dec 25, 2008 | 1993 Isuzu Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...