Question about 2005 Chrysler Pacifica

1 Answer

2005 Pacifica Wiper Hi-Lo Relay chatters when car is powered up, many other items not working at this point....electric windows, blower motor, front wipers, headlights, gear shift release out of park, radio...probably few others.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,122 Answers

Hi Terry, The problems on your vehicle would seem to be too many to be a coincidental failure of so many circuits at one time. I suggest you look for a common denominating factor, such as poor earthing at a major point. It may require you remove seats and carpeting and even parts of the consul. I suspect there will be one multi earthing point which has either worked loose or was not tightened and has worked loose, causing your problems. Proving my theory will be easier than finding the fault. Take an electrical cable and earth it securely. Once earthed, touch it to each of the defective units in turn and observe the operation of each unit controlled by that circuit. If they begin correct operation, you've solved the problem. Regards John

Posted on Oct 13, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Possible fuse or electrical problem 2000 Chrysler Town and Country LXI

my chrysler grand voyager 1999 jumps out of drive gear .and when i rev it .it sometimes jumps into gear.. i have had trans fluid put in and it work ok for 2weeks .but now its doing it again .. please help

Posted on Oct 07, 2008

  • 1596 Answers

SOURCE: 2005 Town Country front blower motor inop fuse/relay ok

Break Down And Replace The Blower Motor


REMOVAL

WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE, THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PERFORMING FURTHER DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE WAY TO DISABLE THE AIR-BAG SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS COULD RESULT IN AN ACCIDENTAL AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL INJURY OR DEATH OR DEATH.

NOTE: The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed from the vehicle without having to remove the HVAC housing.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the passenger side cowl trim panel.
  3. Position the carpet to access the front upper screw that secures the air inlet housing.
  4. Remove the recirculation door actuator.
  5. Disconnect the blower motor wire lead connector from the blower motor resistor or power module, depending on application.
    1. Remove the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing.
    2. Remove the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing.
    3. Push the rubber grommet through the opening in the lower air inlet housing.
    4. Route the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
    5. Position the recirculation-air door as necessary to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
    6. Gently flex the recirculation air door downward to gain access to remove the blower motor from the HVAC housing. NOTE: To aid in installation, note the position of the blower motor mounting tabs prior to removal
      1. Remove the blower motor from the HVAC housing by rotating and tilting the blower motor as necessary.
      INSTALLATION

      1. Gently flex the recirculation-air door downward to gain access to install the blower motor into the HVAC housing.
      2. Position the blower motor to the HVAC housing and tilt and rotate the blower motor as necessary to install it into the HVAC housing.
      3. Align the blower motor mounting tabs to the locations noted during removal and install the three screws that secure the blower motor to the HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      4. Route the blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet.
      5. Position the recirculation door pivot shaft into the lower air inlet housing and install the inlet housing.
      6. Install the four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing. Tighten the screws to 2 N·m (17 in. lbs.).
      7. Install the one screw (from the top) that secures the lower air inlet housing to the upper air inlet housing. Tighten the screw to 2 N·m (17 in. lbs.).
      8. Connect the blower motor wire lead connector to the blower motor resistor or power module, depending on application.
      9. Install the recirculation door actuator.
      10. Reposition the carpet.
      11. Install the passenger side cowl trim panel.
      12. Reconnect the negative battery cable.
      13. Perform the heater-A/C control calibration procedure.

Posted on Feb 07, 2009

highspeedsan
  • 61 Answers

SOURCE: 2006 chrysler PT Cruiser front wipers stopped working

Sounds like the wiper motor has died.

Posted on Apr 26, 2009

  • 1 Answer

SOURCE: 2004 chrysler pacifica, front blower not working,

replace restor open glove box uplug 4 wire plug and two wire plug put 12 volts two wire plug to mke sure fan works if it does replace restor

Posted on Dec 27, 2009

  • 610 Answers

SOURCE: looking for the relay for

THERE IS A WIPER HIGH/LOW RELAY, AND A WIPER ON/ OFF RELAY. BOTH ARE LOCATED IN THE INTEGRATED POWER MODULE, RIGHT FRONT OF ENGINE COMPARTMENT. RELAY ID SHOULD BE PRINTED ON THE INSIDE OF THE COVER. GOOD LUCK!

Posted on Dec 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the multifunction switch on 2003 ford ranger located for the wiper and dash light


What seam's to be the problem ? Would hate for you to replace the switch an have it not fix the problem .
The wiper's not working ? There is a whole list of thing's that could be the problem . Same for the dash light's ?
Symptom Chart Condition Possible Sources Action
  • The wipers are inoperative
  • Central junction box (CJB) fuse:
    • 16 (30A)
  • Circuitry.
  • GEM.
  • Multifunction switch.
  • Wiper run/park relay.
  • Wiper HI/LO relay.
  • Wiper motor.
  • GO to Pinpoint Test A .
Hooking up a scan tool an checking for DTC'S - diagnostic trouble code's in the GEM module .
GEM Diagnostic Trouble Code (DTC) Index
GEM Diagnostic Trouble Code (DTC) Index DTC Description DTC Caused By Action B1431 Wiper Brake/Run Relay Circuit Failure GEM GO to Pinpoint Test A . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM GO to Pinpoint Test A . B1434 Wiper Hi/Lo Speed Relay Failure GEM GO to the Symptom Chart. B1436 Wiper Hi/Lo Speed Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test C . B1438 Wiper Mode Select Switch Circuit Failure GEM GO to the Symptom Chart. B1441 Wiper Mode Select Switch Circuit Short to Ground GEM GO to the Symptom Chart. B1446 Wiper Park Sense Circuit Failure GEM GO to Pinpoint Test D . B1450 Wiper Wash/Delay Switch Circuit Failure GEM GO to the Symptom Chart. B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM GO to the Symptom Chart. B1458 Wiper/Washer Pump Motor Relay Circuit Failure GEM GO to Pinpoint Test E . B1460 Wiper/Washer Pump Motor Relay Circuit Short to Battery GEM GO to Pinpoint Test E . B1466 Wiper Hi/Low Speed Not Switching GEM GO to Pinpoint Test C . B1467 Wiper Hi/Low Speed Circuit Motor Short to Battery GEM GO to the Symptom Chart. B1473 Wiper Low Speed Circuit Motor Failure GEM GO to the Symptom Chart. B1476 Wiper High Speed Circuit Motor Failure GEM GO to the Symptom Chart. B1840 Wiper Front Power Circuit Failure Open/Short to Ground GEM GO to Pinpoint Test A . - All Other DTCs GEM REFER to Section 419-10.
The multifunction switch has nothing to do with the dash light's
Instrument Cluster and Panel Illumination The instrument cluster and panel lighting system is powered through the headlamp switch and the panel dimmer switch. The instrument cluster illumination is controlled by the output of the panel dimmer switch. The instrument panel lighting circuit provides illumination for the:

Oct 23, 2017 | Ford Ranger Cars & Trucks

1 Answer

Por favor, necesito diagrama de caja de fusibles para Mazda B2300 del 2001


Mazda B-Series (2001) - fuse box diagram Year of production: 2001

Interior fuse panel

Mazda B-Series - fuse box -
interior fuse panel Number Ampere rating [A] Description 1 5 Power Mirror 2 10 Blower Motor Relay, Air Bag Diagnostic Monitor, Passive Deactivation (PAD) Module 3 7,5 Trailer Tow Connector (LH Stop/Turn) 5 10 4×4 Control Module 7 7,5 Trailer Tow Connector (LH Stop/Turn) 9 7,5 Stoplamp Switch 10 7,5 Cruise Control Servo/Amplifier Assy., GEM/CTM, Shift Lock Actuator, Blend Door Actuator, A/C Heater Control Assy., Turn Signals 11 7,5 Instrument Cluster, Main Light Switch, RABS Resistor 13 20 Brake Pedal Position Switch 14 20 RABS Module 10 4WABS Mod., 4WABS Main Relay 16 30 W/W Motor, Wiper Hi-Lo Relay, Wiper Run/Park Relay, Washer Pump Relay 17 25 Cigar Lighter, Data Link Connector (DLC) 19 25 PCM Power Diode, Ignition, PATS 20 7,5 GEM/CTM, Radio 21 20 Flasher 22 20 Auxiliary Power Point 24 7,5 Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay 26 10 Battery Saver Relay, 4×4 Electronic Shift Relay, Interior Lamp Relay, 4×4 Elec. Shift Control Module, Dome/Map Lamp, Instrument Illumination Dimming Module, Restraint Control Module, GEM/CTM, Instrument Cluster 28 7,5 GEM/CTM System, Radio 29 15 Radio 33 15 Headlights, DRL Module, Instrument Cluster 35 15 ISA Horn Relay if not Equipped with Truck Security Module

Engine compartment fuse block

Mazda B-Series - fuse box -
engine compartment Number Ampere rating [A] Description 1 50 I/P Fuse Panel 6 50 ABS Pump Motor 7 30 Powertrain Control Module 8 20 Power Door Locks and Remote Entry 11 50 Starter Relay Ignition Switch 12 10 PCM Memory 13 20 4×4 Motor 16 40 Blower Motor 21 10 PCM Memory 23 20 Fuel Pump Motor 24 30 Headlights 25 10 A/C Clurtch 28 30 4WABS Module 30 15 Trailer Tow 31 20 Fog Lamps, Day Time Running Lamps (DRL) 33 15 Park Lamp 38 10 Left Headlamp Low Beam 41 - Heated Oxygen Sensors 42 10 Right Headlamp Low Beam 45A - Wiper High/Low 45B - Wiper Park/Run 46A 46B - Front Washer Pump 47A 48A - Fog Lamp 48B - Fog Lamp Relay 49 - Full Starter 50A 50B - Fuel Pump 53 - Powertrain Control Module (PCM) Diode 54 - Powertrain Control Module (PCM) Diode 55 - Blower 56A - A/C Clutch Solenoid 56B - Trailer Tow

Jul 04, 2017 | Mazda Cars & Trucks

1 Answer

Y need book for fuse box


Fuses are listed here
* = maxi fuse
1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay
6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay
mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator
Interior fuse panel (mini fuses)
1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**
15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat,

i copied this off another post hope this helps

Oct 09, 2016 | 2003 Ford Explorer

1 Answer

Passenger side windshield wiper working slow


there is 2 wiper motors . 1 for the drivres side and the other for the passenger. sounds like a bad passenger side motor

Dec 21, 2012 | 2005 Chrysler Pacifica

1 Answer

I need a diagram of the underhood fuse block for my 2002 ford explorer. I don't have an owners manual.


Fuse/Relay Location*Fuse Amp Rating* Description
1 60A** PJB 2 30A** BSM 3 20A** Not used (Spare)
4 30A** Rear defrost 5 40A** ABS (pump)
6 60A** Delayed accessory circuit breaker
7 20A** Power point #2 8 — Not used 9 20A** Power point #1
10 30A** ABS module (valves) 11 40A** PTEC
12 50A** Ignition relay/Starter relay
13 40A** Trailer tow battery, Trailer tow turn signals
14 10A* Foglamps 15 15A* Memory (KAPWR)
16 15A* Headlamp switch 17 20A* 4x4 (v-batt 2)
18 20A* 4x4 (v-batt 1) 19 20A** High beam relay
20 30A** Electric brake 21 30A** Front wiper motor
22 20A** Autolamp; Low beam 23 30A** Ignition switch
24 20A* Rear Fog Lamps 25 – Not used
26 15A* Fuel pump 27 20A* Trailer tow lamps
28 20A* Horn relay 29 60A** PJB 30 20A** Rear wiper motor
31 — Not used 32 — Not used 33 30A** Auxiliary blower motor 34 30A** Power seats, Adjustable pedals
35 20A** Rear power point 36 40A** Blower motor
37 15A* A/C clutch relay/Transmission
be7a74c.jpg

Nov 15, 2009 | 2002 Ford Explorer

1 Answer

Abs fuse


Fuses are listed here

* = maxi fuse

1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay

6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay

mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump2.gif relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator


Interior fuse panel (mini fuses)

1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**

15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat, Message center Attached images fuse%20box001.jpg?imgmax=800 __________________

Oct 29, 2009 | 2003 Ford Explorer

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

2 Answers

Diagram of fuse panel under dashboard


2003 Excusion, V10, 2wd, Eddie Bauer

I had a hardtimefinding this informaton, hope it helps.

fuses
Fuse link
cartridge
2A Grey Grey — — —
3A Violet Violet — — —
4A Pink Pink — — —
5A Tan Tan — — —
7.5A Brown Brown — — —
10A Red Red — — —
15A Blue Blue — — —
20A Yellow Yellow Yellow Blue Blue
25A Natural Natural — — —
30A Green Green Green Pink Pink
40A — — Orange Green Green
50A — — Red Red Red
60A — — Blue — Yellow
70A — — Tan — Brown
80A — — Natural — Black
Passenger compartment fuse panel / power distribution box
The fuse panel is located below and to the left of the steering wheel by
the brake pedal. Remove the panel cover to access the fuses.
Roadside Emergencies
To remove the fuse panel cover,
turn the panel fasteners
counterclockwise.
To remove a fuse use the fuse puller
tool provided on the fuse panel
cover.

The fuses are coded as follows.
Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
1 15A* Adjustable pedals
2 20A* Power point -floor console
3 20A* Power point – 3rd row
4 20A* Power point -instrument panel
20A* Power point -right rear quarter
6 20A* Trailer tow turn/stop relay
7 30A* High beam headlamps / Flash to pass
8 — Not used
9 20A* Heated mirrors
10A* A/C clutch
11 20A* Radio (main)
12 20A* Cigar lighter / OBD II
13 5A* Power mirrors/switches
14 15A* Daytime running lamps
10A* Driver’s seat module memory
16 15A* Rear seat controller
17 15A* Exterior lamps
18 20A* Turn lamps/Brake on-off switch (high)
19 10A* Body security module/4x4 module
— Not used
21 25A* Rear wiper motor
22 20A* Engine control
23 20A* Engine control
24 15A* Air suspension
10A* 4-Wheel Anti-Lock Brake System
(4WABS) module
26 10A* Airbags
27 15A* Ignition switch Run feed
28 10A* EATC module module/Front blower relay
coil
29 10A* Customer access
Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
30 15A* Highbeam headlamps
31 15A* Clutch interlock switch
32 5A* Radio (start)
33 15A* Front wiper
34 10A* Brake on-off switch
35 10A* Instrument cluster
36 10A* PCM Keep-Alive
37 15A* Horn
38 20A* Trailer tow park lamps and backup lamps
39 — Not used
40 20A* Fuel pump
41 10A* Instrument cluster
42 15A* Delayed accessory
43 10A* Fog lamps
44 10A* PATS module, transceiver
45 10A* Ignition switch Run/ Start feed
46 10A* Left-hand lowbeam
47 10A* Right-hand lowbeam
48 10A* Rear wiper motor
101 30A** Trailer tow electric brake
102 30A** Door locks/Body security module
103 50A** Ignition switch
104 40A** Heated backlite
105 30A** Injector driver module
106 30A** Front wiper main
107 40A** Front blower motor
108 40A** Auxiliary blower motor
109 30A** Heated seats
110 50A** Ignition switch
111 30A** 4WD/Shift on the fly
112 30A** Left-hand power seats

Roadside Emergencies
Fuse/Relay
Location
Fuse Amp
Rating
Passenger Compartment Fuse Panel
Description
113 30A** Starter motor
114 30A** Right-hand power seats
115 20A** Trailer tow battery charge
116 30A** Ignition switch
601 30A CB Door window motors
602 60A** 4-Wheel Anti-Lock Brake System
(4WABS) module
210 — Not used
211 — Not used
212 — Not used
301 — Front blower motor relay
302 — Powertrain (EEC) relay
303 — Injector driver module relay (Diesel
only)
304 — Heated backlite relay
305 — Trailer tow battery charge relay
306 — Delayed accessory relay
307 — Starter relay
* Mini Fuses ** Maxi Fuses

Jan 27, 2009 | 2002 Ford Excursion

1 Answer

Windshield wipers


From your owners manual:

Fuse#11 30A , Wiper Run/Park
Relay, Wiper Hi/LO Relay, Windshield Wiper
Motor, Rear Washer Pump Relay

U will also need to check the relays if the fuse is ok, the relay, it is the underhood fuse box
Relay #202 — Front Wiper Run/Park Relay

Dec 18, 2008 | 2001 Lincoln Navigator

1 Answer

Front wiper does not work


I have the same problem

Jul 29, 2008 | 1996 Plymouth Voyager

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...