Question about Cars & Trucks

Open Question

How do i remove tail light assembly from a 2010 hilux

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Fixe_You
  • 1800 Answers

SOURCE: replacement of rear outside tail light assembly

If you're asking how do you change a taillight bulb, then follow this procedure:

Open the trunk lid.

Disconnect the connectors from the taillights (taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps.) There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.


Brake Lights/Taillights: 21/5 W

Rear Turn Signal Light: 21 W

Back-up Light: 21 W

Rear Side Marker Light: 5 W


Turn the bulb sockets 45 º counterclockwise to remove the bulbs.


If you're removing the taillamps with the bumper off there are 3 nuts and screws that hold the taillight to the rear panel of the car that have to come off from the inside of the trunk.
Remove the nuts and screws, then remove the taillight.

hope that answers your question

Posted on Aug 15, 2008

Ad
  • 2 Answers

SOURCE: cannot remove tail light assembly

I had the HARDEST time with the lights...I never realized changing a bulb would be so difficult. Once you unscrew what you need to, go into the trunk and pull the lining away from the back part of the light. There are the white prongs that you will need to tap with a hammer until they pop out and then the light assembly will come out. Be careful though, I got a little too impatient and broke mine. I used a binding agent to hold it back in place though...GOOD LUCK!

Posted on Nov 29, 2008

  • 28 Answers

SOURCE: 2006 mercury mariner. stupid tail light assembly.

they are hard to take off sometimes, you are doing it right just keep willing it it will come off, there is 2 gromits that hold it into place might have a little dirt into the plunger.

Posted on Feb 22, 2009

  • 1986 Answers

SOURCE: How do you replace rear tail light assembly?

Open the trunk and along the bottom of the tail light, there should be a Philips screw securing a cover piece. (your car may or may not have this piece)
With the cover off, there will be another 2 screws securing the bottom of the tail light assembly. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out

Posted on Oct 13, 2009

  • 564 Answers

SOURCE: cant remove the tail light assemblies on '09 accord sedan

youll have to pull up very firmly or it may have to slide to the side its held in place by a bodyfastener. a screw that fits into a slot. but i would try pulling up first.

Posted on Dec 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

To replace a blown turn signal light on a 2010 dodge avenger ?


front or rear cause ya may not have to remove any screws on headlight assembly's ya have to get to the back where the wires hook up and twist the socket to get to the bulb same on tail lights but ya have to go through the trunk

Dec 28, 2014 | 2010 Dodge Avenger SXT

1 Answer

How to remove 2010 toyota tail light assembly


Either 2 screws on side of assembly when door is open or behind assembly on inside will b 3nuts u must loosen and assembly should fall out.. may have to slightly pry on edge of light to pull a tab

Aug 31, 2014 | 2010 Toyota RAV4

1 Answer

The tail light and the front fog lights don't want to turn off. They only turn off when I take the batery out


light relay faulty, contacter inside relay stuck in connected positon, constantly sending voltage to the lights no matter switch or key position.

Dec 13, 2013 | 2010 Toyota Hilux 3.0

1 Answer

How to replace brake light on 2010 lincoln mkz


Wrong! 2010 MKZ tail lights are LED style. They can not be changed individually. You have to replace the whole assembly.

May 21, 2012 | 2010 Lincoln MKZ

1 Answer

Tail light instrument panel and parking light not working hilux 1984 deisel


Hello. I know youprobably allready have the answer. I a just posting here for future use.


There is a relay to the left of the clutch on my 1996 Hilux. This was causing a similar problem for me. It is found on the left side, iside the car, left of the clutch pedal.

Apr 04, 2012 | Cars & Trucks

1 Answer

How to replace stop light bulb in 2010 dodge caliper


open the trunk, look behind the tail light assembly, if any carpeting exists move it out of the way to reach screws that link to the light assembly, remove them, and the assembly should pop off, then simply remove the old bulbs and put in the new ones. make sure you have the correct size. check modifiedlife.com for size

Jun 08, 2011 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

How to change break lights


Tail Lights
  1. Open the endgate or liftgate.

  2. Remove the screws that retain the tail lamp assembly to the vehicle.
    32085_blaz_g0151.gif

    Tail lamp assembly removal

  3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.

  4. Remove the bulbs from the sockets.

To install:

  1. Install the bulbs into the sockets.

  2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.

  3. Install the tail lamp assembly to the vehicle.

  4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).

Oct 23, 2010 | 2000 Oldsmobile Bravada

1 Answer

How can I remove a tail light assembly to replace a lamp?


Posted by Pmlove509 on Aug 30, 2010

James spams again.

Aug 30, 2010 | 2003 Isuzu Axiom

1 Answer

How do you replace a 2007 Honda Odyssey Tail Light


Yes, you have to remove the plastic panel. It is mostly held by spring clips. You can see how to remove it at the link below.
http://www.odyclub.com/forums/52-2005-2010-odyssey/52868-can-t-open-liftgate.html

Aug 20, 2017 | 2007 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...