Question about Cars & Trucks

Open Question

Mazda Etude 2003 speedometer not working - Cars & Trucks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
elias_sgr
  • 163 Answers

SOURCE: Mazda etude alternator genarting excessive heat

1st off you would give everything a good visual examination. Look for loose alternator belt. Also look for wires that could have become disconnected or cut that leads to the alternator.

Then you would hook up a volt meter to the battery cables and check the voltage.
After this you would start the engine and recheck the voltage. The voltage on a charged battery should read around 12.5 volts. While the engine is running turn on a few accesories and speed up the idle a little the voltage should read around 14.5 volts.

If the voltage does not increase suspect either a faulty alternator or regulator.

Posted on Sep 09, 2008

Ad
  • 1 Answer

SOURCE: Mazda Etude 160ie timing

I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Posted on Nov 27, 2010

  • 70 Answers

SOURCE: I need to Bleed the Brakes of my Mazda Etude 160i 5 door 2003 model

Lynn, Bleeding your brakes is quite an involved process that takes training by a properly qualified expert. I would suggest taking your vehicle to a mechanic this time and then doing a "Mechanical Repairs" course later.

Posted on Oct 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bypass immobilizer Mazda etude 2003


If it is an after market device, remove it. If a Mazda product, it is part of the system.

Mar 09, 2017 | Mazda Cars & Trucks

1 Answer

Mazda etude 1.8 no spark


If you do not have any spark ( petrol engine ) check for distributor cap, rotor arm, ignition module inside the electronic distributor, or any loose wiring connected on distributor or ignition coil or any wire.Also check and the HT Leads.

Jul 02, 2014 | 2003 Mazda 323

1 Answer

Mazda etude clutch problem


sounds like a throw out bearing to me but it could just be a spring popping

Jan 29, 2014 | Mazda Cars & Trucks

1 Answer

Mazda etude


mazda Hi,
Here's a very convenient DIY.. I bought this book 2 years back for my ford endeavour
I bought it for my brother yesterday for mazda rx7 and so landed up here. Try it once, mate. All the best

Nov 02, 2017 | Cars & Trucks

1 Answer

Mazda etude familia not producing spark to the engine while the distributor has a spark


The rotor under the distributor may be bad, pulled the cap and turn the engine over look at the rotor and make sure its turning. If it doesn't turn the distributor gear maybe sheared, timing belt or timing chain may have come off.

Dec 18, 2013 | 2003 Mazda MPV

1 Answer

Mazda etude 1.6 i cut out while driving starting after about 10 min.


sounds like the coil pack is braking down when hot. check for spark while engine wont start

Nov 16, 2011 | 2003 Mazda MPV

1 Answer

My 160i etude 1997 misfires and even mazda agents


it is not carburated injectors are most likley leaking

Dec 15, 2009 | Mazda MAZDA3 Cars & Trucks

2 Answers

Mazda Etude 160ie timing


I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Jan 02, 2009 | 2004 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...