Question about 2005 Acura TL

Open Question

Po717 main shaft speed sensor - 2005 Acura TL

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Malibu error codes po700,po716,po717


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination

Which one of these transmissions does your Malibu have ?
Automatic Transmission - 4T45-E
Automatic Transmission - 6T40/6T45
Automatic Transmission - 6T70/6T75

Do you know how to find out look at the VIN # ?
DTC P0716: Input Speed Sensor Performance
DTC P0717: Input Speed Sensor Circuit Low Voltage
The automatic transmission input speed sensor (ISS) is a permanent magnet with a coil of wire wound around. The ISS mounts in the case cover facing the reluctor wheel of the input shaft. As the reluctor wheel is driven by the turbine shaft, an AC signal is induced in the input speed sensor. Higher vehicle speeds induce a higher frequency and voltage at the sensor. There is a fixed air gap between the sensor and the teeth on the sensor reluctor wheel. The ISS input is used by the transmission control module (TCM) in order to control line pressure, torque converter clutch (TCC) apply and release, and transmission shift patterns. This sensor is also used to calculate the appropriate gear ratios and TCC slippage. This diagnostic indicates stuck, erratic, or intermittent conditions in the system.
Diagnostic Aids
• Road test the vehicle while monitoring the Transmission ISS parameter on the scan tool. The Transmission ISS parameter should vary with engine speed changes and not abruptly drop out.
• Inspect for an open or shorted AT ISS wire.
• Inspect for a disconnected AT ISS connector.
• Inspect for a faulty AT ISS.

Trouble Code P0717 Input speed sensor

Jan 19, 2017 | Cars & Trucks

2 Answers

Where is the vehicle speed sensor located? The scanner read code PO717.


On the transmission, drivers side. In front of the main harness. It is the input speed sensor. small plug.

Aug 08, 2015 | 2008 Jeep Grand Cherokee

1 Answer

What is the problem? I have a code flashing PO717 from a diagnostic scan on my 1996 Olds Aurora.


The PO717 code is for the transmission input speed sensor, or the wires. The sensor is located inside the transmission.

Jun 14, 2014 | 1995 Oldsmobile Aurora

1 Answer

I got a code from obd2. po717 turbine speed sensor circuit malfunction


code po717 refers to turbine shaft speed (TSS) sensor-no signal===causes --wiring--TSS sensor--TCM/ECM .Replace the sensor first .

Aug 23, 2013 | Kia Cars & Trucks

1 Answer

How do you fix code po717 on a 2008 scion xb ?


Code is for a speed sensor in the transaxle. You could have it replaced or tested.

Jul 02, 2012 | 2008 Scion Xb

1 Answer

Po717


P0717 Input/Turbine Speed Sensor A Circuit No Signal, no its not what you may think,, don't go looking for a turbo or anything, heres what it means

The computer wants to know if the transmission is working properly. So it reads the speed of the input shaft and compares it to the speed of the output shaft. It knows which gear you're in because it commanded the transmission to shift into that gear. So, with the input speed, the gear selection, and the output speed, the computer can calculate how efficiently the transmission is working. If the speed is off, it knows that something is slipping inside the transmission. It can then try to boost the fluid pressure to compensate. If that doesn't work, it sets a different trouble code.

The P0717 code means that the computer isn't getting any signal from the sensor. Either the sensor is dead or there's a circuit issue (bad wiring, etc).

Sep 22, 2011 | 1999 Pontiac Grand Prix

1 Answer

I have a nissan altima 05 3.5L engine service light just came on and my scanner read these codes P0722 and p0717 p0462 and p0500 are these things i can fix on my own?


CODE PO462 FUEL TANK LEVEL SENSOR VOLTAGE LOW. CODE PO717 TURBINE SHAFT SPEED SPEED SENSOR NO SIGNAL. CODE PO722 OUTPUT SHAFT SPEED SENSOR NO SIGNAL. CODE PO500 VECHICLE SPEED SENSOR CIRCUIT MALFUNCTION. SOUND LIKE YOU HAVE TCM ECM PROBLEMS GETTING TOO MANY CODES. COULD HAVE LOOSE GROUND WIRE TO THE TCM AND ECM.

Aug 06, 2011 | 2005 Nissan Altima

1 Answer

Two cods on my 2005 scion tc , po717 and po793 what is the solution to these cods.


P0717 SCION - Turbine Speed Sensor Circuit No Signal.
P0793 SCION - Intermediate Shaft Speed Sensor A.

Jan 14, 2011 | 2005 Scion tC

1 Answer

I have a 2006 buick lacrosse my check engine light keeps going on and off and then it starts to **** and drag on speed when its on.. I took it for a test and it says PO455 Evap Large leak, PO716 Input...


You might need to replace your sensor. Also, replace your alternator belts before you change sensor. The drag on speed is caused by the "check engine" light getting on.

Dec 02, 2010 | 2005 Buick LaCrosse

1 Answer

98 Buick Park Avenue (Turbo) P0717 fault code,


CODE PO717 IS - A/T INPUT SHAFT SPEED SENSOR LOW INPUT CONDITIONS.YOUR INPUT SHAFT SPEED SENSOR COULD BE DEFECTIVE.CHANGE FLUID + FILTER IF IT HAVE NOT BEEN CHANGED IN A LONG PERIOD OF TIME.

May 29, 2010 | 1998 Buick Park Avenue

Not finding what you are looking for?
2005 Acura TL Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...