Question about Toyota Tundra
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Removal of the plenum is pretty straight forward. You will need to replace the plenum gasket after you remove it; the gasket is not reusable. Personally, if I was going to take the trouble to remove the plenum, I would replace the plugs and wires back there, also.
I know, I have a 93 Camry V6, and it is a real pain to do the plugs and wires with the plenum on. There are no secrets or great tips on the plenum removal, just take your time. Remember that there are different size bolts, and where they go. Please get back to me if you need any more info...Hope this helps, and thanks for choosing FixYa to resolve your issue.
The graciousness of a FixYa rating for my assistance would be greatly appreciated.
Posted on Dec 15, 2008
SOURCE: replace valve cover gasket
I have the same problem on a 2003 Town & Country. The cover for the front 3 cylinders is quite straight forward, but in order to do the rear cylinders I believe you are going to have to remove the cowling below the windshield. You will need a gear puller to remover the windshield wipers first, then remove the cowling. Than should give you more room to work. It's still not going to be easy, but it sure beats paying hundreds of $$$$ in labor charges.
Posted on May 04, 2009
The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced.
Posted on May 06, 2009
SOURCE: Replace fuel filter
1. Open the hood and access the relay panel on the Right side of the engine bay
2. Open the fuel cap
3. Start the engine
4. Pull the relay for the fuel pump (listed on the bottom side of the relay panel lid)
5. Wait for engine to stop
6. Turn key off
7. Disconnect negative battery cable
8. **** wheels to car
9. Slide under the driver's side around the B pillar area
9. Look on the interior side of the frame rail and you will find the filter assembly
10. Place a drain pan under filter
11. Disconnect the rigid fuel line with a 14mm opne wrench (I think)
12. Disconnect the quick coupling on the aft part of the assembly buy lifting up on the red plastic pience and turning
13. Unbolt the center bolt and pull out the filter
14. Pop in the new filter and reverse order.
Posted on Dec 12, 2009
Tips for a great answer:
Apr 02, 2015 | 2002 Toyota Sequoia
Aug 28, 2014 | 2002 Toyota Sequoia
Aug 29, 2013 | 2002 Toyota Camry
Nov 23, 2012 | 2006 Subaru Forester
Jul 23, 2011 | 2002 Toyota Sequoia
Feb 27, 2010 | 2002 Toyota Sequoia
Oct 24, 2009 | 2006 Toyota Sequoia
Jul 30, 2009 | 2002 Toyota Sequoia
Jul 07, 2009 | 2002 Toyota Camry Solara
140 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: