Question about Cars & Trucks

Open Question

Torque settings for rocker cover bolts on a 1hz?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

  • 1 Answer

SOURCE: need torque specs

Valve Rocker Arm Bolt 19 N·m + 30° (14 lb ft+ 30°)
A GM dealer shows me another source, which says 32 Nm (24 lb-ft). Not sure which one is right but they screwed up my car.

Posted on Mar 17, 2009

  • 14036 Answers

SOURCE: What are the torque specifications for rocker arm

torque 89 inch pounds then plus additional 30 degree turn.

Posted on Nov 19, 2009

  • 617 Answers

SOURCE: intake manifold bolts torque and rocker arm torque

Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Posted on Feb 06, 2010

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

Leaks oil from rocker cover. repaired 3 times. is this a common fault? what is the solution?


The rocker cover will leak oil..............

1. If the rocker cover has been damaged due to poor mechanical fitment and is no longer perfectly straight; or
2. The rocker cover bolts are not torqued evenly at the correct ft/lbs specification; or
3. If the rocker cover bolts have been excessively torqued in which event the cover will distort and the gasket will be excessively compressed; or
4. The gasket is in poor condition and needs to be renewed; or

5. The gasket fitting is sloppy done in which event you can assume the cover will not have been properly fitted either.

I would be buying a new rocker cover (or a straight used one) before doing the next repair because your original is probably deformed now and will likely never seal properly.

Nov 28, 2015 | Cars & Trucks

2 Answers

How to install rocker arms on a Pontiac grand am 2001 V-6


Hi there:

Rocker Arms & Pushrods


Removal & Installation

3.1L & 3.4L Engines
Left Side

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system to a level below the coolant pipe on the front of the engine.
  3. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableSpark plug wiresHeater bypass pipePositive Crankcase Ventilation (PCV) valve and hoseRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm).Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).PCV valve and hoseHeater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).Spark plug wiresNegative battery cable
  3. Refill the cooling system.
  4. Start the vehicle and verify no leaks.




3_4_2013_5_26_48_pm.gif


Right Side
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableAlternator bracket on 2005 modelsSpark plug wires from the spark plugs and the upper intake plenum wire retainerPower brake booster vacuum pipe from the intake plenumAccessory drive beltAlternator, if necessaryIgnition coil assembly and Evaporative Emissions (EVAP) canister purge solenoid as an assemblyRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm) plus an additional 30 degree turn.Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).Ignition coil and EVAP solenoid assemblyAlternator, if removed. Torque the bolts to 37 ft. lbs. (50 Nm).Accessory drive beltPower brake booster vacuum pipe to the plenumSpark plug wiresNegative battery cable
  3. Start the vehicle and verify no leaks.





Hope this helps.

Mar 04, 2013 | Cars & Trucks

1 Answer

I have oil leakin on top of my spark plug wires in the tube ive changed the valve cover gasket 3 times i even put high heat cilcone over around the spark plug tubes but all it does is slow it down im not...


Two things:

1. Make sure you torque the bolts down to the right specification, which is 83 inch pounds (or about 7 ft lbs). Work opposite end of the cover and start with a lower torque first (like 50 in lbs), then go up to 83. It's just a good practice.

2. If that does not work, get a Fel Pro gasket set VS50365R (pic below). What is special about this set is the really thin o-rings there in the middle. Those are the rocker arm tube seals. You need to take the rocker arms off in order to replace them, but this way you're doing a complete job and you probably won't have that issue again. If you don't want to get the whole set again (since you already replaced most of it 3x over), you can probably just go to a honda dealership and pick up the 4 you need.


44db60b.jpg
Here are the seals under the rocker arms:

ea6e49b.jpg
If you decide to do this yourself, it's a good idea to get a set of feeler gauges so you can properly gap the clearance from the rocker arms to the valves. Intake valves should be gaped to .010 in, and exhaust valves to .012 inches. Also, yes, you can take the rocker arm assembly off without removing the distributor...just take off that one bolt that is in the way. The torque for the bolts holding in the rocker assembly is 9 ft-lbs for the smaller 6x1mm bolts and 16 ft-lbs for the larger 8x1.25mm bolts. Here is the torque sequence...

94f3f23.jpg

Oct 06, 2010 | 1992 Honda Accord

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

2 Answers

I need rocker torque for 2003 pontiac with 3.1liter


Left side:

To install:
  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:
    • Pushrods and the rocker arms and tighten the bolts to 14 ft. lbs. (19 Nm) plus 30 degrees
    • Rocker arm cover using a new gasket and tighten the rocker cover bolts to 89 inch lbs. (10 Nm)
    • PCV valve to the rocker arm cover
    • Coolant tube with the thermostat bypass hose and tighten the bolt to 98 inch lbs. (11 Nm) and the nut to 18 ft. lbs. (25 Nm)
    • AIR check valve pipe and torque the adapters to 22 ft. lbs. (30 Nm)
    • Engine mount strut and torque the bolt to 35 ft. lbs. (48 Nm)
    • Spark plug wires
    • Negative battery cable
Right side:

To install:
  1. Lubricate all the valve train components with engine oil.
  2. Install or connect the following:
    • Pushrods and the rocker arms and tighten the bolts to 14 ft. lbs. (19 Nm) plus 30 degrees
    • Rocker arm cover using a new gasket and tighten the rocker cover bolts to 89 inch lbs. (10 Nm)
    • Power brake booster vacuum pipe to the plenum
    • EVAP solenoid and ignition coil assembly
    • Spark plug wires
    • Alternator bracket and torque the bolts to 37 ft. lbs. (50 Nm)
    • Alternator and torque the bolts to 37 ft. lbs. (50 Nm)
    • Accessory drive belt
    • Negative battery cable
  3. Start the vehicle and verify no leaks.

Feb 06, 2010 | 2003 Pontiac Grand Prix

1 Answer

I have 4.9L6 need torque specs for cylinder head


for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Dec 05, 2009 | 1988 Ford F 150

1 Answer

Blown head gaskit need to remove head and replace with new ong


2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Accessory drive belt
    • Air cleaner outlet duct
    • Engine mount
    • Intake manifold
    • Exhaust manifold
    • Engine Coolant Temperature (ECT) sensor electrical connector
    • Power steering pump
    • Radiator inlet pipe
    • Spark plug wires
    • Rocker arm cover

    NOTE Whenever valve train components are removed, keep them in order for installation purposes.

    • Rocker arms and pushrods
    • Lifters
    • Alternator rear brace and the alternator
    • Power steering pump
    • Radiator inlet pipe
    • Ignition coil assembly
    • Accessory bracket
    • Spark plug wires
    • Cylinder head bolts

    WARNING Two sizes of bolts are used; note the location of each.

    • Cylinder head
  5. Inspect the cylinder head and block surface for cracks, nicks, heavy scratches and flatness.
b9d2546.gif
Cylinder head torquing sequence—2.2L (VIN 4) engine

  1. Install or connect the following:
    • Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.
    • Lifters
    • Pushrods and rocker arms. Torque nuts to 22 ft. lbs. (30 Nm).
    • Rocker arm cover. Torque the bolts to 89 inch lbs. (10 Nm).
    • Spark plug wires
    • Accessory bracket
    • Ignition coil assembly
    • Radiator inlet pipe
    • Power steering pump. Torque the bolts to 22 ft. lbs. (30 Nm).
    • ECT sensor electrical connector
    • Exhaust manifold. Torque the nuts to 118 inch lbs. (13 Nm).
    • Alternator. Torque the bolts to 37 ft. lbs. (50 Nm).
    • Intake manifold. Torque the bolts to 17 ft. lbs. (24 Nm).
    • Engine mount. Torque the bolts to 55 ft. lbs. (75 Nm).
    • Air cleaner outlet duct
    • Accessory drive belt
    • Negative battery cable
  2. Refill and bleed the cooling system.
  3. Start the vehicle and inspect for leaks.

Oct 08, 2009 | 2000 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...