Question about Chevrolet Cars & Trucks

Open Question

Disc brakes size socket remove caliper - Chevrolet Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: What size torx socket do I need to take caliper off?

most likely a t50

Posted on Feb 10, 2009

  • 323 Answers

SOURCE: Instructions for removing the rear disc brake pads

7mm

Posted on Apr 22, 2009

  • 1 Answer

SOURCE: waht size allen key to remove front brake calipers

On my Golf 1.9TDI (2005) both top and bottom Calliper fastenings have a 7mm Allen bolt thus you will need a non standard 7mm Allen Key not 12 point

Posted on Jun 02, 2009

  • 1 Answer

SOURCE: tool to remove front brake caliper to replace rotor Escape 2005

You need a 7mm socket, which are available at auto parts stores.

Posted on Apr 24, 2010

ZJLimited
  • 17970 Answers

SOURCE: what size mm hex socket is needed to remove the

Tools:
1. Combination Wrench Set
2. 3/8 in. Drive Ratchet
3. Floor Jack
4. Jack Stand Set
5. C-Clamp
6. Mallet Hammer
7. Flat Head Screwdriver
8. Socket Set
9. Tire Iron
10. 1/4 in. Drive Torque Wrench

Supplies:
1. Brake Cleaner

Steps:
Step 1 Park your vehicle on a solid level surface. Set the parking brake and chock the rear wheels.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Remove the front wheel hub caps if applicable. Using a tire iron, break loose the front wheel lug nuts but do not remove.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 3 Using a floor jack, lift up the front of your vehicle.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 4 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds or the frame rails are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 5 Remove the front wheel lug nuts. Remove the front wheels and set them aside.

Step 6 Inspect the brake caliper for any signs of binding. Look for rust and uneven brake pad wear.

Step 7 Remove the brake caliper mounting bolts (sliding bolts).

Step 8 Support the caliper up and away from the working area. Make sure you do not kink or pinch any brake lines.
o Tip: Use a bungee cord to secure the brake caliper out of the way and hang it on the suspension spring.

Step 9 Clean the sliding bolts and lubricate them.

Step 10 Install the new caliper over the brake pads and rotor. Attach the caliper to the mounting bracket with the sliding bolts. Tighten the caliper sliding bolts to manufacturer’s specifications.

Step 11 Disconnect the brake line from the old caliper. Attach the brake line to the new caliper using new copper washers. Tighten the banjo bolt.

Step 12 Repeat for the other side. Bleed the front brakes.

Step 13 Reinstall the front wheels. Torque the lug nuts to the manufacturer specifications in a star pattern.

Step 14 Remove jack stands and lower the vehicle to the ground.

Step 15 Verify that you have a solid brake pedal. Road test the vehicle to verify brake caliper repair.

Hope this help (remember rated this).

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove the brake caliper on a 1994 f350 4x4 there are no bolts attaching it


If this is a Pin Slider, here is 1996 steps:

Section 06-03: Brakes, Front Disc 1996 F-150, F-250, F-350 4x2, 4x4, Bronco and F-Super Duty Vehicles Workshop Manual
REMOVAL AND INSTALLATION Caliper
Heavy-Duty Rail Slider, F-Super Duty
Replace brake shoe and lining (2001) as follows when the lining is worn to a minimum thickness of 0.794mm (1/32 inch) above the front disc brake rotor shield. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always replace all brake shoes and linings on an axle. Never replace only one wheel (1007).
Removal
  1. To avoid fluid overflow when the caliper pistons are pressed into the caliper cylinder bores, siphon or dip part of the brake fluid out of the brake master cylinder reservoir (2K478). Discard the removed fluid.
  1. Raise the vehicle and install safety stands. Remove the front wheel and tire assembly.
  1. Place an appropriate size C-clamp on the disc brake caliper with end of clamp against caliper and end of screw against outer shoe. Tighten the clamp to bottom the caliper pistons in the cylinder bores. Remove the clamp. Do not use a screwdriver or similar tool to pry caliper pistons (2196) away from the front disc brake rotor (1125).




  1. Clean excess dirt from area around pin tabs.
  1. Tap upper caliper pin toward inboard side until pin tabs touch the front wheel spindle.
  1. Using Hydraulic Caliper Pin Remover D89T-2196-A or equivalent and a light hammer, drive the pin from the disc brake caliper as follows:
    1. Position the notched end of the tool against the caliper pin (retention tab half), at a 45-degree angle from the pin retention tabs.



    1. Tap the tool with the hammer to compress the retention tabs.



    1. As the retention tabs are compressed, move the tool to gain a straight approach to the caliper pin, and continue tapping to drive the caliper pin through the caliper/spindle groove.
  1. Repeat removal procedure for lower caliper pin.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not let the disc brake caliper hang by the front brake hose (2078). The front brake hose could become stretched or twisted which can cause the front brake hose to leak and rupture, resulting in failure.
    Remove the disc brake caliper from the front disc brake rotor. If the disc brake caliper is to be removed for service, remove the front brake hose from the disc brake caliper. Plug the end of the front brake hose to prevent fluid loss and entry of air into the system. If the disc brake caliper is not to be removed, wire it up to the frame of the vehicle to avoid damage to the front brake hose.
Installation
stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always replace all brake shoes and linings on an axle. Never replace only one wheel.
  1. NOTE: There is a raised section at one end of each shoe so installation can be made in one direction only.

    Install new inner and outer lining.
  1. Lubricate the knuckle upper and lower inner pad grooves and caliper grooves with Disc Brake Caliper Slide Grease, Silicone Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A. Install the disc brake caliper on a front wheel spindle, making sure the mounting surfaces are free of dirt.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the tabs of the caliper pin to be tapped too far into the spindle groove. If this happens it will be necessary to tap the other end of the caliper pin until the tabs snap into place. The tabs on each end of the caliper pin must be free to catch on the spindle flanks.
    Position caliper pin with the pin retention tabs oriented adjacent to the spindle groove.
  1. Tap the caliper pin on the outboard end with a hammer. Continue tapping the caliper pin inward until the retention tabs on the sides of the caliper pin contact the spindle face. Repeat procedure for the lower caliper pin.


Oct 23, 2011 | 1994 Ford F350 Crew Cab

3 Answers

What tool do I use to remove the calipers to replace disc pads?


I believe it uses a "hex head". You can buy a set of them from most auto parts stores, Sorry I don't remember the size right off hand.

Jan 12, 2011 | 2001 Kia Sephia

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

How do remove rear rotors on 2004 ford sport trac


Caliper removal

  1. Disconnect the brake hose.
  2. Remove the bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
--------------------------------------------------------------------------------------------
Disc Removal and Installation
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and retract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc. For additional information on machining brake discs, refer to Section 206-00 .
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
---------------------------------------------------------------------------------------------
Installation
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

Dec 17, 2009 | 2004 Ford Explorer Sport Trac

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

Need to replace Discs and left rear rotor, what tools are needed?


Once the wheels are off you will need metric sockets and possibly metric wrenches.I believe the sizes are 10mm in rear to get the calipers off and 13mm in front. but have a range of metric sockets available. You will also need a c-clamp or large channel lock pliers to compress the caliper piston back into the caliper on the front and rear befoer installing the new brake pads and caliper back onto the vehicle.
Good luck with the repair.

Apr 20, 2009 | Jeep Grand Cherokee Cars & Trucks

3 Answers

Rotors


See Figures 1, 2 and 3
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in .
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the two 6mm screws from the brake disc.
0900c1528005fbe4.jpgFig. 1: Remove the two 6mm screws securing the brake disc
  1. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  2. Remove the caliper bracket.
0900c1528005fbe5.jpgFig. 2: Remove the bolt and guide pin from the caliper bracket, then remove the bracket
  1. Remove the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly and alternately to prevent cocking the rotor.
0900c1528005fbe6.jpgFig. 3: Remove the brake disc from the caliper assembly
  1. Installation is the reverse of the removal procedure.
  2. If equipped, enable the SRS system and connect the negative battery cable.5f83e91.jpg810cd9d.jpg14f1553.jpgFig. 1: Remove the two 6mm screws securing the brake Fig. 2: Remove the bolt and guide pin from the caliper
  3. Fig. 3: Remove the brake disc from the caliper assembly
Good luck...........

Oct 24, 2008 | 1992 Honda Accord

1 Answer

2003 Hyundai Tiburon Gt rear brakes


hi not conversant with the tiberon in uk but will try to help ? if you remove the rear wheel then look at the brake disc (rotor) most hyundai rear discs on uk models are secured to the rear hub by 2x screws posidrive or tork heads ? if this is so on yours then no problem you will have to remove the caliper first from the carrier 2xbolts h/brake off then undo 2xbolts securing caliper carrier tosuspension stub assy your disc /s are most probably vented discs? or may be standard discs? remove the screws then you may have to hit disc from behind with hammer to jolt free as they are sometimes rusted on due to high temps and rain ideal conditions to create rust as you prob know? re assemble is reverse hope this helps ?

Oct 20, 2008 | 2003 Hyundai Tiburon

2 Answers

How to replace brake pads


I am on vacation and need to replace my front disc pads. What tools do I need to buy( C-Clamp, sockets, what tool is needed to remove caliper bracket)?

Jul 21, 2008 | 2004 Dodge Grand Caravan

2 Answers

2002 Pontiac Grandam, Rear Brake Pad Change


no 10mm or 12mm you will also need a ebrake caliper reset tool

May 29, 2008 | 2002 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...