Question about 2007 Ford F-150 Harley Davidson

Open Question

Changing the vct of a 2008 ford edge - 2007 Ford F-150 Harley Davidson

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: i have ford edge 2008

my 2008 ford edge some times am on motion it pick gear

Posted on Sep 15, 2013

Ad
  • 460 Answers

SOURCE: i have ford edge 2008

Fuel filters clog up just like air filter and oil filters. Their job is keep crud out of the engine. All three are important to change. The oil filter every oil change (every 5000 clicks on conventional filter). The air filter - urban driving - every other oil change. The fuel filter - good name brand fuel - every 100,000 clicks, not so good brand of fuel - every 50,000 clicks (cheaper fuel or old gas stations can present more contaminants -- as can an old cars gas tank interior). Gasoline contains water, water in the metal storage tank, water in the metal gas tank, water in the metal gas lines (end result rust!). underground storage tank also present opportunity to introduce dirt to fuel.

Dirty fuel filter can reduce engine efficiency/fuel economy. Can also present low fuel flow by fuel pump and that can present fuel starvation to the engine. As well harder work for the fuel pump (bringing on premature failure).

Posted on Jun 17, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

2 Answers

When shouldpcv be changed on 2008 ford edge


If you are able, get a original part and change it following the services / warranty list of parts, that the dealer change according the miles. If you buy the PCV in a regular auto store; more frecuently, maybe half the time. Hope this helps. Take care.

May 15, 2014 | 2008 Ford Edge

1 Answer

Changing the belt on a 2008 ford F 350 6.4 Diesel


some times my 2008 ford edge can't pick gear

Aug 28, 2013 | Cars & Trucks

1 Answer

How do I change a vct solenoid on a 2007 f150 5.4


The VCT solenoid is located under the valve cover toward the front. There are a total of two solenoids, one on each bank (side). If you look at the valve cover you will see a harness and connector going to the solenoid with the top of the solenoid sticking through the valve cover. Remove the valve cover for the affected side, place a shop rag at the timing chain area to keep debris or bolts from falling in. Unfasten the solenoid and simply pull it straight out. Replace the solenoid, remove the rag and reinstall the cover. Be sure to remove the rag :o)

That being said, the main cause of VCT codes or a noise from the VCT is caused by the camshaft phaser. This is the mechanical part of the VCT system and mounts to the front of the camshaft. It operates by oil pressure that is controlled by computer signals to the solenoid.

If the solenoid is sticking, I've had luck taking a 12 volt power source and applying power and ground to the two pins at the solenoid, touching the terminals a few times. This sometimes frees the solenoid and brings the vehicle back to normal cam timing. A fresh oil change with a factory motorcraft filter will help keep the system clean and free from VCT concerns.

Some aftermarket oil filters will start to come apart, sending paper into the oil channels. This affects the oil pressure, the very pressure that the VCT system needs to work. I hope this info helps. If for any reason you can't give four thumbs up, please request more information. Good luck!

Apr 11, 2011 | 2007 Ford F-150 Harley Davidson

1 Answer

Have a code p0010 on my 06 ford fusion. where do i find it for bank 1. or what is causing it


P0010 - Intake Camshaft Position Actuator Circuit Open Bank 1

Possible Causes:
- Variable Camshaft Timing (VCT) position circuit is open or shorted
- Variable Camshaft Timing (VCT) position circuit poor electrical connection
- Faulty Variable Camshaft Timing (VCT) position solenoid

Jan 03, 2011 | Ford Fusion Cars & Trucks

2 Answers

Had build up on the battery post. I cleaned the posts and the radio will not come on now. I checked all the fuses and they are still good.????? 2008 ford edge


Try to see if it lights up, maybe it is asking for a activation code. Otherwise check if the fuse behind the radio is ok.

Sep 30, 2010 | 2008 Ford Edge

2 Answers

Ford edge fuel filters


About every 50,000 miles, unless it is a flex fuel model, then probably every 30,000.

Dec 13, 2009 | 2008 Ford Edge

Not finding what you are looking for?
2007 Ford F-150 Harley Davidson Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...