Question about Jeep Liberty
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
If the 2005 Montana is similar to the 2001 Montana, I have a solution. First you'll need a hexagonal wrench (the 6-sided L-shaped wrench). The tail light assembly is held on by two screws. You'll need the hexagonal wrench to remove them, because a normal screwdriver won't do it. I also had to use a conventional adjustable wrench to get the leverage to turn the hexagonal wrench, because the screws were in there pretty tight. Once you remove the two screws, the whole tail light assembly should come off. Mine required a little force and I had to play with it a bit, but it came off without a lot of work. There will be one set of wires that connects the tail light assembly to the rest of the minivan--try not to damage that set of wires. Once you get the tail light assembly off, you'll have to take apart the assembly that actually holds the lights. No tools should be required. It's held on by four plastic catches. Just undo the catches (easier said than done, but still not too tough) and it comes apart. Then you can pop out the old light and pop in the new light. Then re-assemble. For me, it went back together much easier than it came apart.
Posted on Jan 03, 2009
It probably will cost a few bucks to get the code reset, but you don't need to go to the dealership, most shops with a good scanner equipped for air bag code reading will be able to diagnose and reset the light. The most probable reason for the code is the battery being dead for a while, there is a capacitor in the airbag circuit to make sure the airbag can go off in a collision even if the battery disconnects itself in the process. There is a slim chance it might be something else but either way the shop should be able to tell you what the problem is, and get it fixed... But, just for fun, before doing all this, i'd disconnect the battery for 30 minutes to an hour and reconnect it back, some systems do effectively reset themselves this way.
Posted on Jan 13, 2009
put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from
Posted on Mar 01, 2009
It's the bulb. There are two filliments in the bulb. One is for when you turn your lights on and the other is for breaking and blinker flashing. When the break filliment goes bad it causes the blinker to flash very rapidly. 100% the bulb. Change it and all will be good again. P.S. if it were a fuse none of the break lights or blinkers would work.
Posted on Apr 20, 2009
Tips for a great answer:
Jan 16, 2014 | 2010 Jeep Liberty
Jun 21, 2011 | 2005 Jeep Liberty
May 14, 2011 | Jeep Liberty Cars & Trucks
Jan 22, 2011 | 2005 Jeep Liberty
Nov 21, 2010 | 2004 Jeep Liberty
May 08, 2010 | 2006 Jeep Liberty
Feb 05, 2010 | 2005 Jeep Liberty
Jul 02, 2009 | 2005 Jeep Grand Cherokee
Nov 16, 2008 | 2004 Jeep Wrangler
78 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: