Question about 2000 Acura TL

Open Question

Replace front turn signal bulb on 2000 Acura 3.2TL

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: trying to replace a front headlight bulb on 2001 acura 3.2 TL

Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.

btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.

Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.

If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.

If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)

Posted on Jan 05, 2009

outdoorsman5
  • 631 Answers

SOURCE: Tail lights not working

Did you check your switch for your tail lights. You need to probe the wires from the switch to make sure you have power coming out of the switch.

Posted on Jul 30, 2009

alicantecoli
  • 22156 Answers

SOURCE: Acura Legend 1991. trying trying to fix front turn signal..

buy a new one ,or solder 2 wires to the bulb and then join this to the two existing wires of the loom,drill a hole in the bottom of the bulb holder so the wires can run through it so you use the old bulb holder to hold the bulb in place in the light

Posted on Nov 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the front lower yellow turn signal bulb?


To replace turn signal bulb,click the link below :---http://howtobyme.blogspot.in/2012/02/how-to-replace-front-lower-turn-signal.html
---------This procedure will help.Thanks.

Feb 29, 2012 | 2000 Buick LeSabre

1 Answer

2000 Cavalier: replacing signal bulb on 99 cavalier drivers side ...


remove the mounting screw on the lens, then remove the top 2 bolts holding the headlamp, pull headlamp out to gain access to the mounting nut on the turn signal. Remove the nut and the turn signal light will pull straight out allowing you to replace the bulb.

May 17, 2010 | 2000 Chevrolet Cavalier

1 Answer

My check engine light and TCS light came on in my 1999 Acura 3.2TL. I had the code cleared out and it appears to be running fine. The code came up 1705 Transmission sensor out of range. No one including...


acura 1999 3,2tl .check engine light on ,my computer show code P0141 , 02 HEATER CIRCUIT, [BANK 1, SENSOR 2] please to help find problem .thank you

Mar 16, 2010 | 1999 Acura TL

1 Answer

How to change the right front turn indicator on


1.Remove the front turn signal assembly mounting screws and slide the assembly forward, out of the vehicle body.
2.Twist the bulb socket a quarter turn counterclockwise, then remove the bulb assembly from the housing
3.The defective bulb can then be removed from the socket and replaced.
4. Installation of the front turn signal assembly is the reverse of removal.

Dec 31, 2009 | 2000 Ford Excursion

1 Answer

Acura Legend 1991. trying trying to fix front turn signal..


buy a new one ,or solder 2 wires to the bulb and then join this to the two existing wires of the loom,drill a hole in the bottom of the bulb holder so the wires can run through it so you use the old bulb holder to hold the bulb in place in the light

Nov 15, 2009 | 1991 Acura Legend

1 Answer

Turn signal bulb 2000 Mercedes s500


If you have a owners manual then the method is described there.

Sep 13, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

1 Answer

2000 sunbird front turn signal bulb


only i could replace mine where to remove clips from the black wheel well cover then the light bulb un screws from the back of the lens

Apr 07, 2009 | 2000 Pontiac Sunfire

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2000 Acura TL Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...