Question about 1995 Mitsubishi Mighty Max

Open Question

1994 mistubishi mighty max rear axle seal removal

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 131 Answers

SOURCE: 1991 mighty max

If it is 4X4 and you re not going far. Put the transfer case in neutral. If it is 2X4 standard transmission, put it in neutral. If it is an automatic transmission you need to remove the driveline.

Posted on Jul 10, 2008

Ad
  • 393 Answers

SOURCE: wheres the oil pump located

on bottom of engine inside oil pan

Posted on Dec 09, 2008

  • 523 Answers

SOURCE: Torque specs for mighty max

Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Posted on Oct 15, 2009

  • 1757 Answers

SOURCE: need firing order for 1994 mighty max pickup

I do not know if you have the 2.4L or 3.0L.
However I have included both below, although I think you should have the 3.0L

For the 2.4L:
Firing Order:
1-3-4-2

Cylinders:
(back of engine)
.......4
.......3
.......2
.......1
(front of engine)

Distributor:
.......(back)
..........(2)
....(4)
(+)...............(+) -screw
...............(1)
.......(3)
.......(front)

For the 3.0L:
Firing Order:
1-2-3-4-5-6

Cylinders:
(back of engine)
5------------6
3------------4
1------------2
(front of engine)

Distributor:
.......(back)
.................(+)-screw
..........(2)
(1).................(3)
(6).................(4)
(+) .....(5)
........(front)

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Mar 01, 2010

  • 1 Answer

SOURCE: my maintenance required light is

To the right of the steering column on the dashboard is a switch - most likely the hazard switch. pry out. Look inside. To the right and up should be a silver switch with a black piece. Toggle to either left or right. Will shut off light

Posted on Jul 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for installing the crankshaft for the 2.4 mitymax motor?


Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi
Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Oct 02, 2015 | Cars & Trucks

1 Answer

How to change a rear axel seal on a 1993 mighty max ?


MAIN SEAL TAKE TO A SHOP
OUTER SEAL IS A PAIN ALSO
PINNION NEEDS TO BE SET RIGHT
PULL ALL GUTS OUT OF REAR END
AND SHAFTS THEN PRY OUT SEAL AND TAP NEW SEAL
IN PLACE THEN REASSEMBLE

Mar 09, 2015 | Cars & Trucks

1 Answer

How do you check for trouble codes on a 1994 Mitsubishi Mighty Max p/u


you have near of fuse box black plug 8 pins x2 or 7 x2 that is the plug for obd =plug for scaner engine light folow manual

Aug 08, 2012 | 1994 Mitsubishi Mighty Max

2 Answers

1994 buick roadmaster, oil leaking out of right rear axle, checked brake fluid is full, could it be differential oil leak @ end of axle??


If what you see leaking is very oily and does not evaporate, likely it is an axle seal. If there are no leaks in the brake system, that's the only thing back there that can leak. If the axle bearing is going away, it can damage the seal so make sure you look for small shiny metal flakes behind the seal when you replace it or you will be doing the job again very soon. Can't remember...that IS rear wheel drive right?

Dec 01, 2009 | 1994 Buick Roadmaster

1 Answer

1994 gmc rear axle removal how to


-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

Jul 26, 2009 | 1994 GMC Suburban

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

How to replace my 1994 lincoln towncar rear axel seal


you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

May 23, 2009 | 1994 Lincoln Town Car

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

Not finding what you are looking for?
1995 Mitsubishi Mighty Max Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...