Question about Toyota Cars & Trucks

Open Question

Torque settings 2.2 ltr mazda petrol engine head bolts

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: audi a6 2 ltr petrol timing marks and torque

ally head 75lbs ,timing marks i honestly cannot remember ,do it old fashioned way time it to no1 with valves closed on no1 then you can see where or what the pmarks should be ,do not use starter motor ,always crank engine by hand 360? to ensure valves clear

Posted on Dec 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

CYLINDER HEAD AND BIG END BEARINGS TORQUE SETTINGS FOR OPEL CORSA 2005 1.6LT PETROL MODEL SOUTH AFRICA


i think the 1.6 ltr was only for some markets the engine i think it may be is! cyl head head with new bolts, 25nm +90 +90 +90 + 45 degrees the big end/conrod bearings 25nm +30 degrees thats if it a vauxhall/general motors engine. it may not be

Sep 29, 2016 | 2005 Opel Corsa 1.6

1 Answer

What is the torque sequence of a Kia Bongo Frontier ?


go google and type in --torque settings for kia jt 3.0 ltr engine
-- if will not be ft/lbs but an angle setting
I personally use nickle anti seize as copper reacts with some metals but is good on exhaust n bolts and nuts

Aug 17, 2016 | Kia Cars & Trucks

1 Answer

Mazda estina petrol head bolts torques


hi
these will be a seies of torque setting followed by a series of torque angle settings.
I f you are using new bolts (which is always a very good practice) the settings are all enclosed in the box.
Do not guess these settings ...they are soooooo important.
most of these bolts are stretch bolts and therefore cannot be reused!
CHECK THIS FIRST. If you get this wrong you will ruin the headgasket and cause many more probs..Dont cut corners.
Google will produce the settings or read the forums.
cheers
Roger

Apr 21, 2014 | Cars & Trucks

1 Answer

Mazda b2600 conrod to cranck shaft bolt torque and head bolt torque


petrol engine will be around 35lb conrod and and with a aluminium head about 65 lbs to be correct but i just pull them up till it feels right ,well looked in all data book for you and its on about 35nm then turn 80% and retighten 90% or some such junk same as the head bolts ,so pull the con rod bolts up with a rachet and this will be about right and the head bolts with a decent snap on bar till you get two ripples in the bicep and this will be about right for a ally head somewhere around 65/70 lbs mark ,please remember that on the assembly line at 3 engines a minute coming along the head bolts are tightened up all at once with one big air gun .None of this silly turn it and release and turn again lark ,do you have any idea how much one of them angle reading torque wrenches cost?? .

Dec 22, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

What are the torque specs of the head bolts of a Mazda protege 94


step 1 17-19 ft/lb
step 2 90 degrees
step 3 additional 90 degrees
engine uses Torque To Yield head bolts
New head bolts must be used when cylinder head is replaced or re-installed

stockam auto

Jul 05, 2011 | 1994 Mazda Protege

1 Answer

I need troque setting for cylinder head bolts for Madza MX3


zjlimited_1139.jpg

Fig. 1: Cylinder head bolt tightening sequence for all 4-cylinder engines


1. Clean the cylinder head bolts and the threads in the block. Make sure the bolts turn freely in the block.

2. Install a new head gasket on the engine block. Make sure the camshaft sprocket timing marks are still aligned, as set during the removal procedure. Install the cylinder head.

3. Lubricate the bolt threads and seat surfaces with clean engine oil and install them. Torque the bolts in 2-3 steps to 56-60 ft. lbs. (75-81 Nm) in the proper sequence.

Hope helps.

Apr 29, 2011 | 1995 Mazda MX-3

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Audi a6 2 ltr petrol timing marks and torque


ally head 75lbs ,timing marks i honestly cannot remember ,do it old fashioned way time it to no1 with valves closed on no1 then you can see where or what the pmarks should be ,do not use starter motor ,always crank engine by hand 360? to ensure valves clear

Dec 21, 2010 | 1995 Audi A6

1 Answer

Need torque specs for 1994 ford escort 1.9 ltr head bolts


Torque new cylinder head bolts in sequence to 44 ft lb. Loosen bolts approximately two turns, then torque bolts in sequence to 44 ft lb. Turn bolts an additional 90 degrees in sequence, then an additional 90 degrees

Torque sequence
9 3 1 5 7
8 6 2 4 10

May 07, 2010 | 1994 Ford Escort

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...