Question about Cars & Trucks

Open Question

I need the wiring diagram for the switch in a berg motion showcase.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1970 dodge truck ignition switch wiring diagram


Ed, 1970 dodge truck ignition switch wiring diagram. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.sweptline.com/tech/70_awire.jpg
http://www.sweptline.com/tech/70wire.jpg
1970 dodge truck ignition switch wiring diagram Google Search

Aug 23, 2016 | Dodge Cars & Trucks

Tip

Power Mirror Wiring Schematic 92 Buick Lesabre 1992 thru 1997 & More


Here is a schematic which my dad & I devised over the course of two hours for the power mirror wiring on our 1992 lesabre, as we couldn't find any wiring info to handle this issue.

http://www.iqmetals.com/else/lesabre/

That's our/my website, and that folder will let you see & get all of the pictures & diagrams

The wiring harness for the power mirror switch was acquired through Rock Auto, and the wire lettering scheme was embossed onto the plastic.
Here's a written breakout of the wires & their locations/purposes.

A= Ground
B= Common Left/Right Motion(Splits to both sides)
C= Common Up/Down Motion(Splits to both sides)
D= Left Side - Left/Right Motion
E= Left Side - Up/Down Motion
F= Right Side - Up/Down Motion
G= Right Side - Left/Right Motion
H= Positive 12V

Now Assuming that all of the power mirrors are wired & color coordinated the same, that would connect....
B -- Light Blue wire of Both Mirrors
C -- Green wire of Both Mirrors
D -- Gray wire of Drivers Side Mirror
E -- Dark Blue wire of Drivers Side Mirror
F -- Dark Blue wire of Passengers Side Mirror
G -- Gray wire of Passengers Side Mirror

In our circumstance we hooked up the power and ground inline with the power window Power(Pink) & Ground(Black) wires which are nearby in the door. The fuse/circuit should easily handle the minor load of power mirrors, even if you were using the windows and mirrors at the very same time... a rarity I do suppose.

647aa8a.jpg
77801ab.jpg
3e90b3f.jpg
f8d21d5.jpg

on Nov 28, 2009 | 1992 Buick LeSabre

2 Answers

Need Headlight switch schematic for testing switch


Your year--make--model didn't post for some reason?
www.bbbind.com
has free wiring diagrams
www.autozone.com
also has free wiring diagrams, you have to register your vehicle then click on vehicle repair guides, go from there, it's free.
If you want to give us year--make--model, I'll find the diagram for you and post it.

Jan 06, 2016 | Cars & Trucks

1 Answer

Motion sensor diagram


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems.

Oct 02, 2012 | Cars & Trucks

5 Answers

The clutch has to be in for my 85-s10 blazer to start and it wont start unless i use a screwdriver on the starter. any answers?


Your diagram is below. Since the starter jumps at the solenoid, the problem would be the ignition switch, the clutch interlock, or the wiring. Check for power at the yellow wire that goes to the switch under the clutch pedal when the key is turned to start. If you have power on the red wires to the ignition switch but no power coming out when the key is turned to start, replace the switch. If you DO have power on the yellow wire, try bypassing the interlock by pulling the connector off and connecting the terminals inside the connector with a large paperclip. If that doesn't work, the purple wire from the interlock to the starter solenoid may be broken. Please let me know if you have more questions.

jturcotte_2404.gif

Oct 16, 2011 | 1985 Chevrolet S-10 Blazer

1 Answer

My motorized seat (passenger) doesn't go fully forward, it does go fully back. It seems to stick, and makes clicking noises. It sounds like something is stuck and preventing the forward motion. ...


The most common cause of the problem you are having is with the switch itself.
The switch needs to be removed and cleaned.This helps in some cases, but if its not helping, then switch has to be replaced.The cost of switch is approx $25.You will have to get it from dealer or from local auto part stores. But first try cleaning the switch.Most probably that will help.In cleaning switch.You will have to remove the switch out, disconnect its wires, then clean both wires and switch contacts with cleaner and then reconnect. -------- For instructions and diagrams to disassemble and remove switch on your Lincoln continental , please click the link below:--- http://technoanswers.blogspot.com/2011/06/passenger-motorized-seat-switch.html ------------- This should help.Thanks.Helpmech.

Jun 10, 2011 | 2002 Lincoln Continental

3 Answers

I need to disable my alarm on a 1997 bmw 528i.


Now im not sure since the manual says your model has the same alarm system as the 328i and on the 328i you can remove the module to disable by doing the following. you can unplug the control module. It is located under the glove box. Climb under the dash on the passenger side and remove a few screws on the trim panel under the glove box. Theres a black control module with a green connector. There should be a lock tab on the connector. press the lock tab and pull out the connector. The alarm should now be disabled. But if it has the special transponder key this may not work.
But if the only reason you want to disable it is because of the motion sensor setting of the alarm for no reason there is a solution for this. To disable the motion sensor, hit the lock button to arm, then hit lock button again within four seconds to disable motion sensor. Red light on rearview mirror should flash four times, then pause, then start flashing on regular intervals. this is most likely the reason if your having the issue where the alarm goes off every 20 minutes.
If you want to completely remove it below is a wiring diagram taken from the manual for you alarm system.
this is from the manual its the alarm wiring diagram.
Battery Constant 12v Positive Wire ( ): Red/White or RedBattery Constant 12v Positive Wire Location: Ignition Switch Harness
Starter Positive Wire ( ): Black/Yellow or Black
Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire ( ): Green
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire ( ): Purple/White or Purple
Second Ignition Positive Wire Location: Ignition Switch Harness
Parking Light Positive Wire ( ): Gray/Purple and Gray/Yellow. Use Both Wires. This vehicle has a dual parking light system that will require 2 extra relays.
Parking Light Positive Wire Location: At Headlight Switch
Power Door Lock Positive Wire ( ): White/Red
Power Door Lock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Power Door Unlock Positive Wire ( ): Blue/Red
Power Door Unlock Positive Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Door Trigger Negative Wire (-): Brown/Gray
Door Trigger Negative Wire Location: At Factory Alarm Plug. The alarm plug is a black 12 pin plug located just behind the glove box.
Domelight Supervision Wire: Turns On With Unlock
Domelight Supervision Wire Location: N/A
Horn Negative Wire (-): Brown/Red or Brown/Yellow
Horn Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): Black
Tachometer Wire Negative Wire Location: At Instrument Cluster
Brake Light Positive Wire ( ): Blue/Red or Green/Red
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only. Factory Alarm Disarm Wire Location: N/A
Factory Anti-Theft System: Transponder Anti-Theft System, Requires Bypass And Extra Ignition Key. The 1997 model year vehicle may require a bypass module and an extra ignition key, if vehicle is equipped with a special key from BMW.
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler
if you require further assistance please let me know and i will help assist you from there. Thanks, Midwest-Tek

Aug 27, 2010 | 1997 BMW 328

1 Answer

I need a volkswagen corrado Window Switch Wiring


this should help , try ebay they have wiring diagram manuals for corrados.

Oct 27, 2009 | 1992 Volkswagen Corrado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...