Question about Cars & Trucks

Open Question

Vauxhall astra 2003 hub torx bolt size

Vauxhall astra 2003 hub torx bolt size

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: vauxhall astra horn

The problem is in the loom in the steering wheel, it requires removal of the airbag and a new wheel loom to be fitted. The loom costs about £15.00 I think.

Posted on May 03, 2009

Ad
  • 1 Answer

SOURCE: change idler pulley

It's a T-40 size, but I removed the bolt by first removing the bracket holding the pulley--I assume you're talking about the alternator idler pulley, the one right below the alternator. The bracket is held in place by three 14 mm bolts which I was able to reach from the top of the engine (after removing the black plastic air tube). I then put the bracket in a vise and "buzzed" off the 14 mm nut using an electric impact wrench ($30 +/- from Heartland of America). Be careful when putting the nut back on--the impact wrench will likely be too much torque!


Posted on Jun 23, 2009

  • 2 Answers

SOURCE: my vauxhall astra engine is reving on its own at

have you had it on diagnostic machine cos i did with mine and ended up being the EGR valve?

Posted on Oct 05, 2009

  • 76 Answers

SOURCE: timing belt on vauxhall astra

is the belt the same size as the one that come off? try taking the tensionor all the way off and then fit the belt

Posted on Feb 08, 2010

emissionwiz
  • 76848 Answers

SOURCE: what size torx bit do i need for the front caliper

T50

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thread size needed for a 1997 grand am rear wheel hub assembly


take out a close bolt (same area)and take it to a bolt /fastener shop. They will be able to measure the size and thread and will supply a bolt to the correct grade requirement;

Dec 25, 2013 | Pontiac Cars & Trucks

1 Answer

How to change front wheel hub on a mk4 astra


Most hub assy's are just bolt off bolt on. You will need to suport car on stands, remove wheel, unbolt brake calliper but not the brake hose & move to side, remove disc, unplug abs sensor, unbolt hub from rear (3 or 4 bolts) Normaly 3 torx bolts on astras (funny looking heads) then reverse the procedure

Jun 26, 2012 | Cars & Trucks

2 Answers

I have a 1998 Holden Astra eng noEL20B24119 and want to know the Head bolt torque settings and sequence. The engine is the transition model with twin tappet cover seals. has the torx star headed bolts.


I cannot find a EL20B in my data,but all Astra listed had the same head sequence as shown:

10 6 2 3 7

9 5 1 4 8

the torque specs for the C20XE,C20NE,X20XEV were all
25nm(18lb/ft),-then 90 deg,-90deg,-90deg.
Z20LET were as above plus an additional 15deg.
Same data for smaller and larger engines(except a couple that were 45deg instead of 15)
Make sure that you replace the head bolts with new,they are torque to yield bolts that are designed to stretch to 'plastic' state,and should not be reused.
Put grease(graphite if you have it) under bolt heads and washers,oil the threads.
Usually the head sets come with the torque specs.
I hope this helps you.

Apr 02, 2011 | Honda Accord Cars & Trucks

1 Answer

How to replace a rear wheel bearing on the rendezvous and does the rear end need to be alined


Loosen the lug nuts. Jack up the car and pull off the wheel and brake drum.Unplug the electrical connector from the hub assembly Unscrew the four Torx head bolts that retain the hub assembly. Holes in the hub provide access to the screws. Remove the hub. Bolt the replacement hub assembly into place. Torque the Torx head bolts to 63 ft. lbs... and it would be best to realign after the work is done to ensure the "tow" is not off

Feb 19, 2011 | 2003 Buick Rendezvous

1 Answer

Do use not ave advice on vauxhall astras


as this is an american website most,if not all, the questions relate to american cars,but there are others like me (english)that have spent time in usa/canada that may answer your questions.....as a matter of interest a vauxhall astra is actually an opel kadet everywhere other than in uk......

Jun 11, 2010 | 2003 Ford Focus

1 Answer

Timing belt on vauxhall astra


is the belt the same size as the one that come off? try taking the tensionor all the way off and then fit the belt

Sep 26, 2009 | 1998 GMC Blazer

1 Answer

Hub Removal


there are 3 bolts on the back side that need to come off they are inverted torxs bolts so you need a special socket this is for the front.On the back hub it is just take the nut off then tap on the hub forward it will come off !

May 23, 2009 | 2003 Chrysler Sebring

1 Answer

Pulling wheel bearing hub off 2003 Cacalier


No get a torx allen type wrench to find the right size moisten a small piece of paper then push it on the bolt to get an impression of the hole size

Mar 29, 2009 | 2003 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...