Question about 1989 Ford Bronco

1 Answer

How do I replace a turn signal switch on a 1989 Full Size Bronco, not a tilt wheel.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 1,249 Answers

You will need to remove the steering wheel...using a steering wheel puller, or a harmonic balancer puller...the turn signal switch is under the steering wheel...unscrew hold downs, trace wire from turn signal switch to under the dash behind the brake pedal, disconnect the connector wire...re-install pulling wire up from floor to inside the steering wheel...sometimes tying the wire to another object, then pull through...hope this helps.

Posted on Oct 11, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: firing order for 1989 full size ford bronco 302

13726548 #1 cyl is front pass side and count to back 1234 are on pass side.5678 are on driver side.# 5 being front

Posted on Apr 22, 2009

  • 6 Answers

SOURCE: 1989 Bronco starts but dies after a couple of seconds

try checking the thermostat control senser. it caused my bronco to start for a second and then die. after a while it would finally start and run for a while then die driving down the road. i changed the thermostat control senser and it fixed all problems of dieing

Posted on May 10, 2009

canbruce75
  • 1776 Answers

SOURCE: removing neutral safety switch

Check out the autozone website at autozone.com and register your vehicle. It is free and will give you access to an online repair manual for the vehicle. The steps for removing the neutral safety switch can be found there. Hope this helped. Best wishes.

Posted on Aug 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 F150 turn signal diagram


Here's the schematic for an 88. Your 91 used the same turn signal/hazard switch.

Note if you purchase another turn signal/hazard switch there are two types.
One is for a tilt wheel and the other is for a non tilt steering wheel.

wol_error.gifClick this bar to view the full image.pg058.jpg

Next picture shows the connector pin out of the turn signal/hazard switch and
how to test the switch.

wol_error.gifClick this bar to view the full image.pg125.jpg

Sep 20, 2012 | 1991 Ford F150

1 Answer

Tilt steering wheel loose 1989 chev truck


Not a fun job sorry!
1) Remove horn button. 2) Remove steering wheel. 3) Remove turn signal/cruise lever and cancel cam. 4) Remove tilt pins with a pin puller(about $10) 5) Tighten the four loose screws that hold tilt mechanism to the column.
Be happy you do not have airbags.

Mar 08, 2011 | 1989 Chevrolet K1500

2 Answers

1989 ford bronco full size 5.8 L V8 I tried to start it... the starter didnt stop turning and kept going even when i took the key out.. wouldnt stop and went until it killed my battery


Just answered identical problem in another make of vehicle. There are 2 possibilities for your problem. A bad Keyswitch and/or a bad Starter Solenoid. I assume your Bronco did not start, which is a good thing. You could have damaged the teeth on the flywheel if the engine started.

You may need to replace the Keyswitch. It is suppose to send a signal to the "tickler" wires on the Solenoid, connecting the Battery to the Starter. Either the Keyswitch shorted and continued to power the Solenoid, or the Solenoid shorted and Welded a connection after the Keyswitch was turned OFF.

Remove the small wires to the Solenoid. If the Solenoid is welded internally, the Battery will spark when you try to connect the Battery cables and the Starter will spin. This would mean the Keyswitch may still be good, do not reattach the small wires yet.

You would need a testlight or Voltmeter to test each small "tickler" wire by attaching the testlight to a Ground and the other end to the tickler wire. When you turn the Key to Start, the light should Glow. It should not Glow all the time.

My advice is to replace both the Keyswitch and the Solenoid because of the wear they encountered with the malfunction. Then when you get the Bronco to start, go to Autozone or Oreillys for a Starter draw test to see if the Starter was damaged by your other problems. Both of those Parts stores test and scan for free.

Sep 26, 2010 | 1989 Ford Bronco

1 Answer

The ignition switch is hanging up in my 1990 ford bronco,


I just had that same problem on a silverado. Yes, you have to replace the switch. Autozone has a tool you can use to remove the steering wheel. If you are not mechanically inclinced you can still do this. Removing the steering wheel sounds scary, or at least it did to me, but it wasnt bad at all.

Aug 03, 2010 | 1990 Ford Bronco

2 Answers

1989 ford bronco full size need to know where or if it has a fuel cut off switch


the right front kick panel covers up the fuel cut off swith. take the kick panel off and a small box with a buttom will appear
press the button in to reset the fuel supply

Mar 24, 2010 | 1989 Ford Bronco

1 Answer

My 1989 ford bronco 4x4 full size,the ignition key wont turn at all,so because its locked up i cant replace key and tumbler from the outside,Is it possible to fix from the inside.


Try spraying brake clean or something to break up the dirt in the tumbler. It is probably gummed up from years of use. If you can free up the pins and springs in the tumbler it will turn. If not you will have to drill it out. Good luck.

Dec 15, 2009 | 1989 Ford Bronco II

2 Answers

Firing order for 1989 full size ford bronco 302


13726548 #1 cyl is front pass side and count to back 1234 are on pass side.5678 are on driver side.# 5 being front

Apr 22, 2009 | 1989 Ford Bronco

1 Answer

Replaced power steering pump on 1989 bronco 5.0 liter


sounds like air in the system. jack up front of bronco so both wheels are off the ground start up and turn steering wheel back and forth untill all the air comes out, and add fluid as needed. when air is gone winning will go away. be patent it may take a while.

Jan 31, 2009 | 1989 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...