Question about 1998 Ford Contour

1 Answer

Length in cm - 1998 Ford Contour

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

Length of what? If you know the length of whatever it is in inches, multiply it by 2.54 to get the length in centimeters, or 25.4 to get millimeters.

Posted on Apr 19, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size belt do I need to bypass ac compressor on a 2005 pt cruiser?


Use a bit of string or rope to run around all the pulleys without the air con compressor and mark the rope. Measure the length. Most V and flat belts are marked with their size, which is their length in cm. Remember that the compressor pulley may put an angle or bend on the belt for it to run properly and be tensioned properly. If you bypass this, there may be nothing to tighten the belt, or the tensioner may not work as well. You will soon find out if the belt slips, it will squeal like mad.

Apr 09, 2015 | AC Cars & Trucks

1 Answer

Toyota 5afe head bolts torque


Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Mar 31, 2014 | 2003 Toyota Corolla

1 Answer

Relay buzzing under hood with car shut off


Hello!
Is it an electric like buzzing not too loud, or more strong?
I had a problem with the vacuum pump which is located on the left side, a little bit right, below the water coolant expansion tank, it is white and has the size of about 5 cm in length and about 2-3 cm diameter, if you pull down both little black rubber harnesses and it stops, then it was a vacuum pump. Made a quite loud buzzing sound in my car after I stopped the engine. I'd give it a try, only 10 seconds to do the work. If this is the problem you can get one free from a wreck or buy a used one, the don't really go bad too often, I would not buy a new one. But also read the other solutions as this was only my case.

Mar 19, 2014 | 2004 Kia Sorento

1 Answer

Turn signals work but will not turn off after turn the wheel back


remove streering wheel,underneath it should be a pin approx 1- 1.5 cm long if this is missing or bent. replace.you can put a nail in its place of the same length & thickness.grease it before putting wheel back.

Mar 11, 2012 | 2000 Saturn SL

1 Answer

How to replace a door handle on a 2007 hyundai sonata,


our question is vague. If you must replace the exterior handle only, Point 7 in Prakash's excellent answer is enough.
Tip: to repair a broken exterior handle: fill both sides of the broken handle with metal reinforced epoxy like KwikWeld, then push nails (heads clipped off, 4 or 5 cm long, 1.5 or 2 mm diameter) into the small part (over half the length of the nails will stick out), then put the handle back together and wait. The nails will reinforce the epoxy and you'll have several cm of metal totally filling up the handle where it is broken.

Feb 29, 2012 | 2006 Hyundai Sonata

3 Answers

2000 Grand Am GT: I need the firing order diagram for a 2000 pontiac...


2000 Pontiac Grand AM 3.4 liter V-6 VIN "E"

f8fdb07.gif

Hope helps (remember rated this).

May 17, 2010 | 2000 Pontiac Grand Am GT

1 Answer

My brakes lock after a mile or so ive just fitted a new master cylinder and been told its probably the wrong one what the differance between abs an none abs they both look the same ????//


That may be so, but your problem is that you don't have any 'free play' at the pedal and the brakes never fully release. Reduce the length, a small amount, of the rod which pushes into the master cylinder so that it returns clear of the cylinder contact and that you can lightly push on the pedal by hand and feel when the rod makes contact. The free play at the pedal is about 1 inch or ~1.5 cM.

Aug 25, 2009 | Land Rover Discovery Cars & Trucks

1 Answer

I need the following info for my 1999 Audi S3 in relation to the tailgate dimensions: Height.......cm; Length........cm; width.........cm; wight.........kg


Exterior Dimensions
Wheelbase
2519 mm
Front Track
1527 mm
Rear Track
1503 mm
Overall length
4159 mm
Overall Width
1763 mm
Height (unloaded)
1415 mm
Ground clearance
n
Unladen weight in kg / gross weight limit in kg
1375 kg / 1935 kg

Nov 05, 2008 | 2005 Audi A3

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...