Question about Saturn Cars & Trucks

Open Question

P0449 2008 saturn outlook likely fix. i replaced the solenoid under the air intake, but the code still pops up after reset. Is the evap canister vent solenoid the same part as the Purge solenoid under the air intake?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

Ad
  • 160 Answers

SOURCE: 2006 saturn ion 2.2L engine code came up for EVAP purge/vent

replace your pvc vavle then have your cars underbody washed

Posted on Mar 15, 2009

moparownr
  • 667 Answers

SOURCE: locating vacuum canister and testing it

The purge solenoid should be in the hard plastic vent lines that run under the tube between the intake and the air filter, ablove the transmission, it is common for vibration holes to be worn in the hard plastic tubes causing a vacuum leak. The purge solenoid is small and it has an electric wire coming from it. I 'think' your canister is in the front lower left corner under the hood, you may have to remove splash shields to see it. The problem is most likely in the hard plastic lines at the solenoid. Let me know if this helps.

Posted on Oct 27, 2009

  • 1 Answer

SOURCE: HAVE A TROUBLESHOOTING MESSAGE PO446

Evaporative Emission (EVAP) how to find a leak without replacing canister on chevy silverado 1500

Posted on Jan 18, 2010

  • 236 Answers

SOURCE: my ingine check light keep coming on,the code that

oxygen sensor

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does code PO446 mean how do i fix this code problem?


You have an Evap System problem and yes, this can cause poor gas mileage. Possible causes are:
  • Plugged vapor canister
  • Faulty vent solenoid
  • Pinched or blocked EVAP hose
  • Faulty FTP sensor

Jan 05, 2018 | Saturn Cars & Trucks

1 Answer

Where is purge valve solenoid located?


Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube




Dec 11, 2015 | 2003 Saturn VUE

1 Answer

I received the following code for a 2006 Saturn Ion with a 2.4 Litre motor P0446 what is is and how do I fix it?


Trouble Code: P0446

Evaporative Emissions (EVAP) Vent System Performance

Possible Causes:


The EVAP system tests run when the engine is first started and meets the Conditions for Running the DTC. An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill condition.An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission (EVAP) Canister Filter Replacement and Evaporative Emission (EVAP) System Cleaning .Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system.Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.For intermittent conditions, refer to Intermittent Conditions .

Dec 29, 2012 | 2006 Saturn ION

1 Answer

My 00 xterra had a code of po446


Trouble Code: P0446

EVAP Vent Control Solenoid Circuit Malfunction

Possible Causes:


Vent solenoid circuit open, shorted to ground or to power (B+).Vent control solenoid is damaged or has failed..PCM has failed.TSB 00-060 (7/00) contains information related to this code.Trouble Code: P0455

EVAP System Gross Leak (0.080") Detected

Possible Causes:


.EVAP control system pressure sensor is damaged or has failed.EVAP purge solenoid or canister vacuum line loose or off.EVAP purge solenoid is damaged or has failed.EVAP emission canister is dirty, restricted or full of water.EVAP canister vent control valve is damaged or has failed.Fuel tank cap loose, missing or it is the wrong part number.Fuel tank temperature sensor is damaged or has failed.Fuel tank vacuum relief valve is damaged or has failed.Large leak in the EVAP canister or in the fuel tank area.ORVR system is damaged or has a large leak in a component.Refueling control valve is damaged or has failed.Vacuum hose leaking between intake manifold and Purge valve.Here are the codes,take part back and get refund.

Dec 03, 2012 | Cars & Trucks

2 Answers

Obd code p0457 fuel cap replaced mil reset defect not cleared connection checked ok


The code is for a large leak in the EVAP system such as a loose or missing gas cap. But it could also mean a loose or missing hose to the canister or other leak in the tank.
The computer vents the tank several times an hour while the engine is running, and it checks the system by pressurizing the gas tank. If the tank will not hold pressure the code is set.
You may have to check the top of the tank where the fuel pump gasket is, as well as the vent lines to the front of the car.
A mechanic would perform a smoke test to look for leaks.

Jul 23, 2012 | Honda Accord Cars & Trucks

2 Answers

P1443 code problem. How do I fix this?


P1446 - EVAP Canister Vent Control Valve Close
EVAP canister vent control valve remains closed under specified driving conditions.

This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows EVAP Control System (Small Leak) diagnosis.

The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

About the possible causes that your must solved:
- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with water


Hope this helps.

Apr 27, 2011 | Mercury Cougar Cars & Trucks

3 Answers

What is evaporation control system malfuction mean? The code is P0440


Hi, the computer has sensed through the fuel tank pressure sensor that the vapor cannister is not evacuating properly. I have pasted details on the EVAP system below. Check the purge valve on top of the engine as shown below (#1 in picture). Make sure the electrical connector is on the valve, that the wires are not damaged, and check the hose for kinks. If all looks good, I recommend you replace the valve. A new valve is $23 at autozone. Please let me know if you have more questions and thanks for using FixYa.

jturcotte_1020.gifjturcotte_260.jpg
Description & Operation
EVAP Canister
The canister is filled with carbon pellets used to absorb and store fuel vapors. Fuel vapor is stored in the canister until the control module determines that the vapor can be consumed in the normal combustion process.
EVAP Control System
The evaporative emission (EVAP) control system limits fuel vapors from escaping into the atmosphere. Fuel tank vapors are allowed to move from the fuel tank, due to pressure in the tank, through the vapor pipe, into the EVAP canister. Carbon in the canister absorbs and stores the fuel vapors. Excess pressure is vented through the vent line and EVAP vent solenoid to atmosphere.
The EVAP canister stores the fuel vapors until the engine is able to use them. At an appropriate time, the control module will command the EVAP purge solenoid ON, open, allowing engine vacuum to be applied to the EVAP canister. With the EVAP vent solenoid OFF, open, fresh air will be drawn through the solenoid and vent line to the EVAP canister. Fresh air is drawn through the canister, pulling fuel vapors from the carbon.
The air/fuel vapor mixture continues through the EVAP purge pipe and EVAP purge solenoid into the intake manifold to be consumed during normal combustion. The control module uses several tests to determine if the EVAP system is leaking.
The EVAP system consists of the following components:
EVAP Purge Solenoid
The EVAP purge solenoid controls the flow of vapors from the EVAP system to the intake manifold. This normally closed solenoid is pulse width modulated (PWM) by the control module to precisely control the flow of fuel vapor to the engine. The solenoid will also be opened during some portions of the EVAP testing, allowing engine vacuum to enter the EVAP system.
EVAP Service Port
The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.
EVAP Vent Solenoid
The EVAP vent solenoid controls fresh airflow into the EVAP canister. The solenoid is normally open. The control module will command the solenoid closed during some EVAP tests, allowing the system to be tested for leaks.
Fuel Tank Pressure Sensor
The FTP sensor measures the difference between the pressure or vacuum in the fuel tank and outside air pressure. The control module provides a 5-volt reference and a ground to the FTP sensor. The FTP sensor provides a signal voltage back to the control module that can vary between 0.1-4.9 volts. As FTP increases, FTP sensor voltage decreases, high pressure = low voltage. As FTP decreases, FTP voltage increases, low pressure or vacuum = high voltage.

Feb 10, 2011 | 2002 Chevrolet TrailBlazer

2 Answers

I have a code P1447 Evap purge flow monitor on my 97 Pathfinder. What is and how do I correct this issue?


P1447 - Evaporative Emission (EVAP) Control System, Purge Flow Monitor
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions. Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.

Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a fault is determined. Malfunction is detected when EVAP control system does not operate properly, EVAP control system has a leak between intake manifold and EVAP control system pressure sensor.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
* EVAP canister purge volume control solenoid valve stuck closed
* EVAP control system pressure sensor and the circuit
* Loose, disconnected or improper connection of rubber tube
* Blocked rubber tube
* Cracked EVAP canister
* EVAP canister purge volume control solenoid valve circuit
* Closed throttle position switch
* Blocked purge port
* Closed throttle position switch


Test is and send us your updated.

Jan 14, 2011 | 1998 Nissan Pathfinder

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

2 Answers

Where is the evaporative fuel solenoid on a 1998 sw2 saturn? i have 2 monitors that with not reset on is the solenoid and the other evap system. i have already changed the gas cap. i do not have a service...


Evaporative Emission (EVAP) Canister Purge Soleno Evaporative Emission (EVAP) Canister Purge Solenoid Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.
id Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.

Oct 07, 2009 | 1998 Saturn SC

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...