Question about 2004 Chrysler Crossfire

Open Question

Where is the resistor module in a crossfire for the ac system?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fan motor was bllowiinghot only on high replaced the ac control module now doesnt blow at all. Is there a fuse or amplifier?


Hi Elaine , What make vehicle are you working on ? Most manufactures have a relay for hi speed an have a blower motor resistor for all other speeds . Depending on make vehicle control modules need programming in some cases . Blower Motor Problems Auto Repair Help

Nov 08, 2015 | AC Cars & Trucks

1 Answer

How can I fix my ac/heater fan ?it stays on when key is shut off


Sounds like the resistor module is miswired.

May 07, 2015 | Cars & Trucks

1 Answer

Ac or heat, fan will not come on


the resistor module is the one suspect, see if there is voltage at resistor then move the speed knob and the voltage will change wire. if it is resistor have to be change. it is the most common problem

Aug 14, 2013 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

The ac works but the switch wont turn on the fan. the rear controls work. its just the front that doesnt. checked the relay switches they seem fine.


Either you have defective blower motor or a defective blower motor resistor module. The resistor module has been known to fail on these trucks. Both items are located behind the glove box.

Sep 11, 2010 | 2004 GMC Envoy

1 Answer

AC ON 2006 CROSSFIRE MALFUNCTIONING


I had to have the dash taken off cleaned out all hoses and replaced the fan....works great now

Jul 08, 2010 | 2005 Chrysler Crossfire

2 Answers

No heat


Have you checked the relay for the system. Should be in the under hood fuse block.

Oct 07, 2009 | 2004 Dodge Dakota

2 Answers

AC only works on settings 3 & 5


souns like a bad blower resistor.the resistor controls the different speeds.sometimes every speed except the highest will stop working.the blower resistor is almost always near the blower motor.

Sep 03, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...