Question about 2000 Cadillac Escalade

Open Question

2000 escalade brake pedal travles to the floor. Replaced master , calipers,have auto bleed the brakes with the abs unit and pedal still goes to the floor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: 2002 escalade brake pad replacement

T- 50

Posted on Oct 21, 2008

Ad
  • 105 Answers

SOURCE: 1993 cadillac deville: caliper problem

on a 1993 Deville I believe that GM installed 2 seperate brake lines from LH and RH leading from the calipers so that if one went out at least you had stopping power in the other caliper. this was done as a safety feature because of past fatalities from previous accidents.

Posted on Jul 26, 2009

j_del
  • 1586 Answers

SOURCE: brake pedal goes all the to the floor. can not

Check the reservoir to be sure the fluid is full. If not, top it off and try it again. If there's still trouble building pressure, pump the brakes a bunch of times, and then check around each wheel for fluid on the ground. If you see none, it's possible that you have a break in the line somewhere through the chassis and that the fluid is leaking out inside. If you see no evidence of leakage, and the reservoir is still full, you need a new brake master cylinder - what will have happened is that the diaphragm around the plunger inside the master cylinder (which moves through the cylinder when you push the pedal, and forces fluid out to the wheels) has a hole or tear in it, so instead of pushing the fluid out to the brakes, the plunger simply moves through the fluid. It never builds pressure, and your brakes don't work.

Posted on Dec 22, 2009

Testimonial: "thanks for the info. very helpful. harry Newman"

Chomby
  • 61 Answers

SOURCE: My brakes will not get

Did you personally change them? Check all wheels and brake lines for leaks. Check if your brake fluid reservoir is full. It sounds like there is air in your brake lines. This guide will help you and a friend bleed your brake lines: http://www.wikihow.com/Bleed-Brakes. If it is leaking somewhere in your lines you may need to replace that section. Comment if you need more help.

Posted on Dec 27, 2010

  • 215 Answers

SOURCE: brake pedal goes to floor, but brake fluid full

Only 2 items can cause that. First one being air in the brake lines. If work has been done on the brake system then they weren't bleed properly. The other is a bad master cylinder.

Posted on Mar 17, 2011

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford f150 lariet - 2000 - change back disc brakes and pads. Have tried bleeding system with vehicle running and off. When it was off and started the brakes pedal goes soft and to the floor. Have tried...


IF the hand brake activates through the caliper piston unit and it was necessary to screw the piston back in to fit the new pads then you will have to readjust the hand brake .. The may be a bleed nipple on the abs unit . It is not necessary to run the engine to bleed the brakes. IF you used a clamp to push the piston back in then there may be crap in the master cylinder that is affecting the operation of the non-return valve at the outlet of the master-cylinder.

Aug 31, 2013 | 1998 Ford F150 Regular Cab

2 Answers

My 1997 chevy 1500 z71 brakes suddenly going all the way to the floor. Checked brake fluid and it was low. Could be wheel cylinder? Master cylinder? or ?


well, check the brake lines for leakage after adding brake fluid to the full mark. If the brake pedal goes all the way to the floor, it's likely there is a leak somewhere after the master cylinder. If the pedal gets hard after adding fluid, and pumping it several times with the car off, then the master cylinder is still ok.

If air has gotten into the master cylinder, it may have to be bled out on a bench, or using a scanner if that's the way your vehicle is.

Bleeding the Brake System (ABS) Auto Bleed Procedure NOTE: Perform a manual bleeding procedure. If the brake pedal height and firmness results are not achieved, perform the auto bleed procedure below.
NOTE: Perform this procedure when replacing the brake pressure modulator valve or electro-hydraulic control unit.
  1. Perform the manual brake bleeding procedure. Refer to Bleeding the Brake System (non-ABS).
  2. Check the master cylinder fluid level often to prevent running the system dry.
  3. Press the brake pedal firmly and run the Scan Tool Automated Bleed Procedure (for Gas engines) once, or the Function Test (for Diesel engines) four times. Make sure to release the brake pedal between each test.
  4. Perform the manual bleed procedure again. This should remove the remaining air from the brake system.
  5. Bleed the system as many times as needed to obtain the appropriate feel of the brake pedal.

Dec 18, 2010 | 1997 Chevrolet K1500

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

3 Answers

Brake pedal all the way to the floor...Possible abs module?


Im going to assume that a mechanic has already checked for the most simple causes like making sure the brakes have been bled. If the abs module is faulty it will default to just a no abs state, but that wont cause the pedal to go all the way to the floor. I agree that replacing the caliper is probably gonna fix the problem, but I might try to bleed the brakes first and see if that solves it first...

Jan 24, 2010 | 2001 Dodge Grand Caravan

1 Answer

Brake pedal goes too far to the floor on initial application, pumping brings the pedal up, bled several times


Sounds like an internal leak in the master cylinder, an external brake fluid leak (such as a leaking brake line), or extreme misadjustment or binding of the calipers or drums. Any could be the case, and you can eliminate the last 2 rather easily. Do you see any sign of fluid coming from any of the brake lines? If not, move to adjustments. Check the calipers for bound up caliper pins and if equiped with rear drum brakes, the adjustment and condition of the rear shoes. After that, go right for the throat and replace the master cylinder. Be sure to bench bleed it before you install it, and if you have ABS, make sure you also bleed the ABS system, OR if you can't bleed the ABS system have the new master cylinder ready to install, and remove the brake lines as quickly as possible from the old master and have a friend hold thier fingers over the ends of the lines. I do this quite a bit at my shop, and it's VERY rare that I actualy need to bleed the ABS after replacing a master cylinder if little to no air gets in the brake lines.

Dec 10, 2009 | 2000 Subaru Outback

2 Answers

Brake pedal dropping to floor


do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.

Oct 18, 2009 | 1994 Chevrolet S-10

2 Answers

Brake pedal still goes to floor 2000 GMC Jimmy


It's very possible to be the master cylinder, the o-rings on the piston could be worn, letting the fluid seep back through instead of getting full pressure through the lines. Could also be the brake booster.
Try changing the master cylinder first, which is cheaper and easier, and see if there is a difference, you'll need to bleed the brakes again.
To check the booster,
With the engine off, pump the brakes until the pedal is hard, then hold pressure on the brake pedal and listen for air escaping, or the pedal goes slowly to the floor, Do that after the master cylinder has been changed, at least that will be eliminated.

Sep 15, 2009 | 2000 GMC Jimmy

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

Not finding what you are looking for?
2000 Cadillac Escalade Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...