Question about 2001 Chevrolet S-10

1 Answer

Motor idels radically -trans. won't shift properly

Engin light stays on. abs light stays on. we have replaced 02 censor idle censor opened cad converter checked all brakes ok checked thouroughly for a vacume leak.

Posted by on

  • yadayada
    yadayada May 11, 2010

    what in the world would the O2 sensor have to do with this? are u guessing?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,000 Answers

If your service engine and ABS light are on, take the vehicle to your local Auto Zone and have the codes read. They will do that for you at no charge. Write the codes down and reply back, we can go from there.
Per your description, it sounds like an EGR valve issue, but get the codes checked and let me know.
Regards,

Posted on Apr 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Lincoln continental idles at 2100rpm and if I try to drive it it won't shift until it reaches 4000rpm


CHECK FOR THE MODULATOR VACUUM LINE THAT RUNS FROM REAR OF ENGINE DOWN TO TRANS.
** ALSO, LISTEN FOR VACUUM LEAK) RECONNECT AND IDLE SHOULD DROP & CAR SHIFT PROPERLY!
**ALSO, IF YOU HAVE NOT HAD A TRANS FILTER/FLUID CHANGE....DO THAT AS WELL!

Jul 26, 2013 | Cars & Trucks

1 Answer

02 mitsubishi galant es 2.4 Problem after engine mount replacement.


There are other possibilities too.........
Get the error code scanned,it will help.

Mar 14, 2013 | Cars & Trucks

1 Answer

How do i replace a nissan murano stepper motor?


The stepper motor is not replaceable on this auto. The ECM and crank sensor controll the idle process for this Nissan. First change your crank position sensor you know the cars computer is ok. This is where i would start. Once this has been accomplished if this did not fix your problem.please return and ask me for me and i will go threw the Idle Air Relearning Process with you. I REPEAT DO NOT DO A RELEARN PROCESS WITH THIS FAULTY CRANK SENSOR ENGINE CAN RACE OUT OF CONTROL DAMAGING YOUR ENGINE AND FRYING YOUR ECM WITH OVER VOLTAGE> Your crank sensor is picking up the wrong signals telling the engine it is rotating at a completely different RPM is what is wrong and that is the reason for the radical RPM and transmission shifts. THe trans is programmed to shift at certain RPMs but it cant change right because the crank sensor it telling it it is at 1100 rpm and its really at 2200 rpm. it is simple computer network failure. Change this and get back to me if you have any other questions

Apr 09, 2012 | 2007 Nissan Murano SE

1 Answer

Idels high shifts hard and that is like every other time started put in new ecm and still have the issue


Your describing a vacume leak or a mis adjusted throttle body. Does it ever idel down? What engine is in it Desiel? If it's gas the AIS motor might be sticking or is bad. Does it run and is the check engine light on? are all the fluilds correct level? coolant level low can make the coolant senser lie about the temperture of the motor to the ecm and it'll command a high idel. Once the idel motor goes as high as it can it might be shicking and you can remove it and wash it off with carb spray and while it's out with the wire connected turn the key on and off with it in your hand and spray it with cleaner till it moves smoothly. With it retracted install it and try again, any vacume leak will make it idel fast. The trans mission will shift hard if the vacume line to it is off and it's on the back of the intake manifold and it goes to a modulater on the side of the trans. it can be off there too.

Dec 19, 2010 | 1995 Chevrolet Suburban

1 Answer

My toyota 4Runner idels fine when it is in park, but the minute I shift it into drive, before even touching the gas it has a hard shaking idel. What could be wrong?


your problem is the idle air control motor it is not adjusting the idle as you shift out of park, normally engine idle has to be bumped up slightly when in gear. yours is not working must be replaced you will find it at the end of the duct work from the air filter at the intake throttle body.

Nov 16, 2010 | 1995 Toyota 4Runner

1 Answer

Rough idle then stalls


Vacume leak or bad idle motor. With the car in park and running with the hood open listen for leaks moving your hand around the different hoses looking for a change in the sounds that you hear. The idel motor also makes the car idel up to 1500 RPM or so right at start-up then idel down, If it doesn;t the idel motor is likly. Check engine light is on when running? Test for codes, Follow code test charts don't skip any steps!.

Nov 02, 2009 | 1998 Chevrolet Malibu

1 Answer

Car not shiftting right. The check engine light came on and we pulled a code of P0507 ''Idle Control System RPM high''. The throttle body was cleaned out with throttle cleaner and the light stayed off for...


THE IDLE SPEED SENSOR SOUNDS LIKE IT IS FAILING. THE IDLE SPEED SOLENOID CAN PREVENT THE TRANS FROM SHIFTING AT DESIGNATED RPM'S. THE THROTTLE POSITION SENSOR WORKS IN CONJUCTION WITH THE IDLE SPEED SENSOR TO TELL THE COMPUTER THE DEMAND FOR FUEL AND THUS SHIFTING THE TRANS AFTER THE RPMS HAVE REACHED ALMOST REDLINE. TRY CHANGING THE SENSOR AND YOU WILL HAVE SOLVED THE NO SHIFT PROBLEM. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING. PLEASE KEEP ME POSTED. GOOD LUCK

Aug 26, 2009 | 1999 Buick LeSabre

3 Answers

Where is the abs control module located on a 02 chevy avalanche ?


THE EBCM IS BAD this is the electronic control module that is on abs pump. you can replace seperate I think it is around 500 for part

Dec 30, 2008 | 2002 Chevrolet Avalanche

1 Answer

03 suzuki aerio automatic transmition won t shift into overdrive


You have two temperature lights that come on when you start the car, one red and one blue. After the car is started the red light goes out and the blue one stays on. According to the manual, (and from my personal experience with my '03 SX), the car needs to warm up to a proper operational temperature. This temperature is reached once the blue temperature light turns off, (or within seconds afterwards). If you don't allow your car to warm up you will notice hard or long shifting, rough idle, and poor engine performance. Never drive your car if the light displays a constant red temperature light.
If this solution does not work see a Transmission expert of take it to your local Suzuki Dealer.

Nov 16, 2008 | 2003 Suzuki Aerio

Not finding what you are looking for?
2001 Chevrolet S-10 Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...