Question about Cars & Trucks

1 Answer

New sensors reset for vehicle - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,187 Answers

Some engines etc take 10 engine starts to reset. or remove the code stored. if everything is fixed. if not you need the codes read.

Posted on Oct 11, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Have a 2001 won't start no spark new crank and can and coil pack code keeps saying its no reference signal from crank position sensor


U need to reset your crankshaft position sensor and camm seror also needs to b reset or they need to b replaced

Jan 20, 2016 | Cars & Trucks

1 Answer

How to reset speed sensor on 2006 Tacoma 4x4


I guess you are talking about an after repair clear of codes to reset computer for the new vehicle speed sensor. Just use an OBD2 code reader and clear current codes drive and see if all your problems are gone. hope this helps

Aug 08, 2014 | 2006 Toyota Tacoma

1 Answer

Mass flow air sensor failure


Question one... What kinda vehicle do y'all have 2.) when the mechanic told ya it was a MAF sensor did he use a computer to tell you this by reading the codes? 3.) after Installing the other MAF sensor did you reset the vehicles computer. I have came across a few vehicles that even after the new part was installed the on board computer will still read in something "like" a safe mode and will not automatically reset itself. Hope this general info helps

Mar 31, 2013 | Cars & Trucks

1 Answer

Reset bmw 530 puncture warning light


The TPMS signal is not idetified by your vehicle,when a predetermine amount of air is not present the sensor turns off. When this sensor turns off .Your vehicle TPMS monitor notice it and turns the light on.Some vehicle needs the TPMS monitor to be reset.Others need to be turned on. Still others just needs a set amount of air pressure to turn on and driven in your case the TPMS monitor should detect the sensor and the light will turn off

Mar 13, 2012 | Cars & Trucks

2 Answers

2006 chevy colorado abs light on changed left speed censor


if you broke sensor wire at the electrical connector.the dealership more likely can get you another sensor connector with new wires splice in new wires and connector.

Nov 12, 2011 | 2006 Chevrolet Colorado

1 Answer

Changed transmission fluid went for test drive and vehicle shut off, is there a sensor that needs to be reset?


There is no sensor I know of, that has a reset

Sensors report data to your vehicles computer

Feb 21, 2011 | 2000 Dodge Caravan

1 Answer

Noticed that warning light on my dashboard is showing service Engine soon confirmed that it is my speed sensor is faulty. how many sensors are on the vehicle and want to replace them.


This is a new one the engine service light is on and its caused by teh speed sensor?? this is a totally new fault showing and iam wondering how you learnt the speed sensor is the cause ,unfortunatly their is no listing for resetting a mitsubishi service light in my alldata book so it looks like its a dealer only job although i bet its possible on this older vehicle somehow ,like holding the trip meter on and then turning the ignition on or the AM/fm button the radio or something equally bizarre

Feb 15, 2011 | 1999 Mitsubishi Montero Sport

1 Answer

Engine light po501 and replace sensor and still won't go off


A P0501 DTC trouble code may be caused by one or more of the following:
  • The Vehicle Speed Sensor (VSS) is not reading (functioning) properly
  • There is a broken/frayed wire leading to the vehicle speed sensor
  • The vehicle's PCM is not correctly configured for the actual tire size on the vehicle
Possible Solutions The simplest thing to do is to reset the code and see if it comes back.
Next, check all wiring and connectors that lead to the speed sensor. The location of the sensor depends on your vehicle. The sensor could be on the rear axle, transmission, or perhaps the wheel hub (brake) assembly.
If the wiring and connectors are OK, then check the voltage at the speed sensor. Again, the exact procedure wil depend on your make and model of vehicle.
If everything looks OK, replace the sensor.

Also, confirm to reset the PCM stored codes.

Hope helps (remember to rate this).

Oct 14, 2010 | 2004 Jeep Grand Cherokee

1 Answer

I got a new front rim after I egged the sockets that the nuts sit it. My tire pressure indicator is still lit up on my dash, even after i replaced the rim. Is there a reset button anywhere? How do i...


sounds like you need to get the tire pressure sensor programmed to your vehicle. the sensor is probably sending a signal but your vehicle is not excepting the data because as far it knows it may be coming from a vehicle parked beside you.

Jun 17, 2009 | 2008 Ford Ranger 2WD

1 Answer

Help


Hello vettechgirl2,
When you replace a tire on a vehicle equiped with a tire pressure sensor system, there are several things you need to be aware of. Hopefully the tire company was careful when changing the tire. The valve stem sensor is about $100.00+ to replace on most vehicles equiped with them. On newer vehicles the tires are filled with nitrogen to keep corrosion down on the sensor. When a tire is replaced the sensor system has to be reset a day or two after the replacement, this allows for breaking in of the new tire. All the tires should be checked for proper manufacturer inflation before resetting the system, including the spare if there is an inflated on on the car. Then the internal computer control can be reset. The owners manual should have instructions on how to reset the sensor program, there is usually a small button under the dash that is used for the reset. Once reset, your system should work as before the flat. If it doesn't stay reset, then the tire place didn't do the installation correctly damaging the sensor or the tire is loosing pressure. Check with your car dealer to see what the tires were originally filled with so you don't mix gases when equalizing the pressure. If your owners manual does not have the reset instructions the dealer may have to set it electronically. Regards, rcampsr

Feb 21, 2009 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...