Question about 1998 Chevrolet Cavalier

1 Answer

How many ignition coils are on a 1998 chevy s10 2.2 L engine?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 50 Answers

Only the one watch this vid;
\http://www.youtube.com/watch?v=pjR_Mk1o6t8

Posted on Oct 11, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: need firing order for a 1998 chevy malibu 3100 v6

The Firing order is 1-2-3-4-5-6. But the wires go on the coils in this order1-4-6-3-2-5

Posted on Mar 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of ignition module on 1998 chevy Blazer?


It is mounted to a heat sink that is mounted right next to the ignition coil on the passenger side of the engine. You can't miss it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 21, 2014 | 1998 Chevrolet Blazer

1 Answer

Cant find the ignition control module for Chevy 3500 Dually


The gas engines should have the module and coil mounted on the intake close to the distributor.

Sep 21, 2012 | 1998 Chevrolet C/K 3500

1 Answer

Can a ignition coil when hot prevent from starting, for a 283 chevy


I would not rule it out ... do you have a substitute you can try for a while? 283, GREAT engine.

Sep 07, 2012 | 1998 Mitsubishi Eclipse

1 Answer

Cant get my 1999 chevy pickup with vortec 4.3 motor to fire at all


You could have got a motor from a non running vehicle. Did you use the distributor and coil from the donor vehicle, or did you transfer your distributor and coil to the used engine you bought? Check to make sure you have power going to the distributor and coil first. If you have fuel getting to the cylinders, and ignition voltage, going to the coil, you might have a problem with the distributor system. Those engines are notorious for this problem More often or not, the ignition module failed. The pickup coil in the distributor has a high failure rate too.

Nov 24, 2017 | Chevrolet Cars & Trucks

1 Answer

Engine turns over, but there is no firing, I replaced plugs, wires, distributor cap and rotor, also replaced fuel pump, what other problems would cause vechicle not to fire. Would it have to be the...


It is possible that the trigger to the HT coil is absent and so there is no HT or firing. So check on the platinum points or the electronic ignition and check the PULSATING voltage on the HT coil negative side.
If there is trigger with no HT output then the coil is faulty. If not check the condenser and the points. Set the gap correctly or replace. If this has an electronic ignition then check the sensor and the circuit if there is a failure.

Aug 02, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I have a 1998 toyota sienna with 132,000 miles on it. Recently I noticed a "shuddering" or hesitation while driving that was intermittent at idle and driving. The check engine light came on...


my name is Jerry Tiet. Base on my experience on 1998 Toyota Sienna with the DTC P0303 show there is a misfire in cylinder #3. a possible cause is the ignition coil of the #3 cylinder. Compare the resistance value of the ignition coil of cylinder #3 with the other coil or simply switch ignition coil #3 with one of the other ignition coil and clear the DTC with the scan tool. Then run engine for couple days. If the check engine light on again. Let me know what is the DTC code.

Nov 11, 2010 | 1998 Toyota Sienna

1 Answer

Cant find sensor.its under the coilpack.but where


It would be easier to help when all the information is given. 98 Chevy S10 P/U What engine? If it is a four cyl the coil pack is on the passenger side (right side) mounted on the engine block. It is a bit hiden but it is there. Follow the ignition wires from the top of the engine all the way down to the other end and you will find coil pack, consequently you will find cmp snsr.

Dec 01, 2009 | 1998 Chevrolet S-10 Pickup

3 Answers

Ignition coil installation


It doesn't have a coil. It has a bank of 3 coils with direct contact to the plugs.
Remove the cover on each side which is on top of the valve covers. This will expose the coil packs.

Jan 27, 2009 | 1998 Cadillac Catera

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...