Question about Mercury Milan

Open Question

Milan 6 way power driver seat wont operate the back of lower seat up or down. it slides forward and back and the front - leg- part goes up and down

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

co7196
  • 3433 Answers

SOURCE: stuck front passenger seat - wont slide back or forwards due to small screw lodged in floor runner

Be there done that, but with a penny. All you can do is either get real aggressive with a hammer and long metal object as a punch or pull the seat. The seat should have 4 bolts. One at each end of each track. Ising a 1/4 in drive rachet and either a 1/2 or 9/16 socket should work. 1/4 in drive is low profile.. good luck

Posted on Jun 02, 2009

MNfisherman
  • 11896 Answers

SOURCE: driver's side front seat won't move

It is likely the gear on the motor came off track with the seat. The seat will have to be removed and bottom panel disassembled.

Posted on Jul 06, 2009

BeninVa
  • 389 Answers

SOURCE: 2001 VW Beetle. The driver's front seat adjuster

I'm assuming you have manual adjustment seats. There is a spring underneath the seat that locks the end of the lever into corresponding notches in the seat frame rail. That spring has either fallen off or broken.

Posted on Jan 22, 2010

  • 1 Answer

SOURCE: 2000 Park ave - power seat problem

The electric adjustment motor has a drive-gear that engages a gear on the shaft of the adjustment screw (90 degree engagement). The gear on the adjustment shaft looses a tooth. Adjustment motor whines, drive gear on adjustment motor spins, no action though because of missing tooth. A 12mm 1/4" drive socket on a wiggler (universal) on the end of a 6" extension can engage the not on the end of the exposed large adjustment shaft and, as the shaft is lightly loaded and the electrical switch engaged, one can get the shaft to spin almost one revolution at a time until the seat is high enough. It is hard to reach the nut necessary (inside the dull-grey clevis that the shaft threads into) and I had to take off the seat pad by removing the 4@ 13mm nuts (and 3 @10mm nuts holding the center section with the driver's cushion) to more-or-less easily access the situation. Dealership wanted well over $1000. to fix it. Three out of my 4 up and down adjustment motors are running, but don't adjust. PS, on my 2001 Park Avenue on each seat there is one adjustment motor for the front edge up and down, one adjustment motor for the rear edge up and down, one adjustment motor for the seat fore and aft, and one adjustment motor for the sear back tilt. Lots of complication, not so much on durability. We do not swap out drivers and adjust the seats excessively. Weak design on the one internal gear. Manually adjust it, unplug the electric to the motor, Drive happy again.

Posted on Aug 13, 2010

leafsveteran
  • 74 Answers

SOURCE: drivers seat wont move forward. power moves the

try tapping the motor that runs the seat back and forth.sometimes the motors get corroded if they are not used often enough.

Posted on Dec 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My driver side seat won't go all the way forward. But when I let it back it goes back and goes down. When I move it forward it lifts up high but don't go forward enough for me.


Seat adjustment ranges are sometimes limited and sometimes there is a fault, such as a coin or something falling into one of the runners.

Cars intended for the premium market often have forward/back, up/down and sometimes tilt adjustment for the driver seat while for the small car, basic or budget market usually only have forward or back. Because on average a person who has shorter legs and needs the seat forward will also have a shorter body so enterprising designers have made the seat runners of some models slope upwards to lift the driver as the seat is moved forward.

Adjustable steering columns are fairly common, though only in the rise/fall plane. I haven't seen a telescopic column for many years. What is really needed is adjustable pedals but designers and manufacturers are very reluctant to go down that avenue, though there are companies specialising in such modifications.

You need to be on the ground on your knees with a good light looking under the seat to see if the available adjustment range takes the seat to the true limit of its travel in both directions.

Feb 28, 2015 | Cars & Trucks

1 Answer

Drivers seat 2000 outback


So here is a diagram of the seat circuitry for your car. Since every other function works except the forward/backward slide function, that leaves basically the forward/backward slide motor, the seat switch, and/or the wiring. If you can verify that the wiring under the seat is in good condition without obstructions, chaffed wires, and/or wires pulled too tight, then it's safe to say it's down to just the motor and/or the switch. Sometimes if the passengers front seat has the same switch, you can plug it in to the drivers' side connector and see what works and what doesn't. If the seat works fine with the other switch, then that's all it needs, if not then it will need a motor. If the other seat doesn't have a switch then you can find them at wrecking yards, or just supply power and ground to the motor in question to see if it works. If it does, then you know you kneed a switch and if not then a motor.
I hope this info helps!~subyguru~
82066173

Nov 14, 2011 | 2000 Subaru Outback

1 Answer

How do iremove front seat from a 1997 honda accord


1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

Jun 16, 2011 | 1997 Honda Accord

3 Answers

How do i take the back off on a 1999 nissan maxima bucket seat


Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6
  1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
03b6e0a.jpg

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
  1. Remove upper rear seat back-to-chassis bolts.
77eb191.jpg

Fig. 4: Remove the bolts behind the center armrest ...

a796228.jpg

Fig. 5: ... and the bolts on the lower corners ...

fbf100a.jpg

Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
  1. Remove rear seat back by tilting forward and pulling straight up.

To install:
  1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
  2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Jan 19, 2011 | 1999 Nissan Maxima

2 Answers

Driver's power seat will not move backward


check fuse.if fuse is good check for power at seat motor.if yes replace seat motor.if no check wires at switch.if wires is not loose or broken seat motor switch could be bad.

Dec 13, 2009 | Dodge Grand Caravan Cars & Trucks

1 Answer

How do i remove the front seats of a 1998 Pontiac Grand Prix?


On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

Sep 01, 2009 | 1998 Pontiac Grand Prix

2 Answers

My front seat will not move forward. It will recline, move up and down but it will not move forward. I've tried reseting the seat positions but nothing seems to work. my seat wont move forward is there a...


You can move the drivers seat back by turning on the power, getting in the seat and position your feet firmly on the fron flor with your back firmly against he seatback, and then engage the switch pushing back - while pushing like hell with your feet. You can actually hear the seat drive shaft turning while the seat moves back. The principle should be the same for moving forward, but pressure would have to be aplide to the back of the seat.

Jun 02, 2009 | 2004 GMC Envoy

1 Answer

Driver's power seat not working properly on 2004 tahoe


it sound like you need to replace seat control switch

May 14, 2009 | 2004 Chevrolet Tahoe

3 Answers

Power front seats


Use a hammer and tap each of the travel rails on seat, this worked great for me, something just gets misaligned in there.

Nov 09, 2008 | 2002 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...