Question about Ford Crown Victoria

1 Answer

Brakes lights won't work

Brakes light won't work

Posted by on

  • 6 more comments 
  • honeybaked21 Apr 23, 2009

    I haven't check the fuse, but to get it out of park, I have put the key in and turn it, then put the car into neutral to start it?

  • honeybaked21 Apr 23, 2009

    also, i don't have an owner's manual to the car

  • honeybaked21 Apr 23, 2009

    Ok I found the fuse box and pulled it off, what number is the brakes lights?

  • honeybaked21 Apr 23, 2009

    No they are only numbered

  • Samuel Charles Spriggs May 11, 2010

    There has to be a diagram somewhere -- an unlabeled fusebox is something I've never seen. I'm going out for the rest of the day/night -- I'll pick up with you tomorrow.

  • Samuel Charles Spriggs May 11, 2010

    The fuse block shoud be labeled either where the fuses plug in, or on the cover, or inside the cover. Are they?

  • Samuel Charles Spriggs May 11, 2010

    The park/neutral problem is probably a switch -- not related to the brake lights.

    Can you look for the fuse box -- it's usually on the kick panel on the driver's side

  • Samuel Charles Spriggs May 11, 2010

    Have you checked the fuse? See owner's manual for location. Please, let me know what you find.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

Change the brake switch at the pedal,its flat,about 1 inch wide,and about 2 inches long,it goes together a certain way so pay attention how it comes apart,about a $5.00 part

Posted on Apr 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Brake lights won't work

Check the voltage or the connection.
Multi-Cardiag M8 CDP for car and truck

Jun 05, 2013 | Cars & Trucks

1 Answer

2001 jeep wrangler. Brake lights won't work but

Check the brake control switch situated just above the break pedal arm under the dashboard. Could be a wire loose or unplugged or the switch itself could be faulty

Mar 07, 2013 | Cars & Trucks

1 Answer

My brake lights won't come on but all lights work

check the brake switch under the dash by the brake pedal. More than likely defective.

Jan 27, 2013 | 2007 Nissan Sentra 2.0 SL Sedan

2 Answers

Brake Lights Won't Light?!

Have you checked the brake light switch by the brake pedal?

Jun 20, 2012 | Cars & Trucks

2 Answers

My 1997 rodeo brake lights won't work

Have you replace or tested the brake light switch at the brake pedal arm under the dash? If not do so, it is likley the problem.

Jan 25, 2012 | 1997 Isuzu Rodeo

1 Answer

Brake lights won't work, what's a cem control unit

For your brake lights...First check your check your brake light switch..that would get your brakes lights working..Now cem control unit??? Do you mean (Climate Control Unit)??

Jun 12, 2011 | 2001 Volvo S80

1 Answer

I replaced a cracked rear tail light with an after market new light. Now the brake light won't work but reverse lights and directional signal do. The bulbs are fine as I've moved them around and...

  • If there are no brake lights period the check the stop switch (brake light switch)
  • This is attached to the upper part of the brake pedal itself. Should be a little wire off of it. When that goes bad the brake lights will not work at all.
  • Please note that the fuse for "brakes" is ABS only and has no bearing on the brake lights themselves working.
Regards, Tony

May 30, 2011 | 2003 Jeep Grand Cherokee

1 Answer

When brakes applied brake light won,t work

If it just the brake light switch, should be under a $100.00.

Jul 21, 2010 | 1994 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides