Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You need to remove the console upper panel, and the center inst panel finish. Remove the screw under the middle knob, and the 4 screws behind the upper compartment door. Disengage the 4 clips and the 4 claws. Pull it straight out. Release the 2 claws that holds the heater control to the inst panel. You should now be able to access the bulbs. This should help you; repost if you have any problems.
Posted on Oct 11, 2008
Well, at least it is easier to repair, the SL/VR4 has an LCD panal that is VERY expensive.
Inside the base's control module are little bulbs, yes, you can take them out and change them, but that is kind of a pain in the ****... you may want to just get a new control module from a junkyard and swap it out. if you don't have a service manual, look for one on CD... sometimes people on Ebay sell them, it will give you complete directions on pulling the unit
If you want to pull it yourself, here is the diagram.
Posted on Feb 15, 2009
look for access panels in rear hatch there will be one on each side remove those and there will be 10 ml nuts holding the light housings on remove those then you can access the lights
Posted on Jul 02, 2009
There is one bulb (for all three knobs) behind the center knob. Turn the knob to the straight up and down 12 o'clock position and pull the knob straight out. Wrap a soft cloth around the jaws of a pliers, that works the best. Pull the bulb out with a needle nose wrapped with a rubber band. The bulb is a sylvania 2721, available at most auto parts stores. You can also use a small piece of vacuum tubing to pull the bulb out. (pull straight out, don't twist it)
Posted on Mar 08, 2010
Tips for a great answer:
Oct 29, 2015 | Mitsubishi Cars & Trucks
Jan 20, 2013 | 2000 Mitsubishi Galant
Nov 13, 2012 | 2000 Mitsubishi Galant
Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.
Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.
Grab the bulb and pull it from the socket with a slight wiggling motion.
Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.
Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.
Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.
Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed. Close the Galant's hood.
Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe
Close the Galant's hood.
Sep 27, 2012 | 2000 Mitsubishi Galant
Apr 22, 2012 | 2001 Mitsubishi Eclipse
Mar 09, 2011 | 2000 Mercedes-Benz C-Class
May 06, 2009 | 2000 Mitsubishi Galant
Jan 29, 2009 | 1999 Volkswagen Passat
Nov 13, 2008 | 2000 Mitsubishi Galant
Sep 24, 2017 | Cars & Trucks
115 people viewed this question
Usually answered in minutes!