Question about Nissan Z
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.
Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.
Hope this is helpful!!
Nissan Scope Technician- 10+ years experience in Nissan dealership
Posted on Nov 11, 2008
SOURCE: Door Panel removal
remove all visable screws from panel and arm rest. Arm rest should come off. Use a flat thin tool or piece of metal and slip it between the panel and the metal door frame. Slip it in about 2 inches,. Slide it back or forth til you hit a stop. That should be a plastic pop in.twist metal tool to pull panel away from the door. It should pop away from door frame. Don't overdo it if it doesn't come out. try another spot. once you get one loose, you can tell how to get the others out. Once panel is loose push it upwards to get top lip out of window bottom. If it has power windows,disconnect plug. If it has manual windows, you will have to remove the window crank There is a snap ring behind window crank that has to be removed.push in on panel by window crank and you can see the ring.
Posted on Dec 06, 2008
This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal
Posted on Mar 20, 2009
You most likley have a damaged inside door handle. To remove the door panel, you must first remove the handle bezel. The trim piece around the handle. It is held in place by 4 retainer tabs, take a small flat screw driver, insert it between the bezel and handle. Gently pry away from the handle. If you look in the crack around the handle you will see the tabs. When you get that off, remove the switch assembly by prying up on it gently, unplug the wiring. There are 2 screws in the door panel where you pull the door shut, remove those also. Start at the bottom front of the door panel, pull outward firmly, but not violent. The retainers will come out, you will most likley break some, this is common. The inside handle is about $45 from your dealer. If it is the handle it is held in with 1 rivit, drill it out with a 3/16 drill. Replace the handle, reassemble. Good Luck.
Posted on May 05, 2009
SOURCE: 54 Micra door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door. It sounds like the linkage connecting the handle to the latch is not working (broken or slipped off)
Posted on Aug 14, 2009
Tips for a great answer:
Oct 30, 2016 | 2003 Nissan 350Z
Apr 15, 2016 | Nissan Cars & Trucks
Oct 09, 2014 | Nissan Sunny Cars & Trucks
Aug 31, 2012 | 2003 Nissan 350Z
Dec 27, 2010 | 2003 Nissan Altima
Jul 02, 2010 | 1994 Nissan Sentra 4-Door
Jan 09, 2010 | 2002 Nissan Altima
Nov 09, 2008 | 2002 Nissan Altima
Oct 16, 2008 | 2001 Nissan Quest
125 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: