Question about Isuzu Cars & Trucks

Open Question

Remove crankshaft pulley

Can't remove the crankshaft pully of my isuzu crosswind, how to remove that

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: broken crankshaft pulley bolt on

The only possibility I can suggest is that which is called and 'Easyout.' These are available at parts stores and come (normally) with a sized drill and a special bit with left-hand threads.
First a hole is drilled with the provided drill bit, then the removal bit is screwed into the new hole and turned counter-clockwise which further inserts the removal bit and, if the removal bit does not snap, the broken threaded shank should back out.
I would suggest soaking the broken part with penetrating lubricant first and allowing it time to seep into the threads of the broken bolt.   

Posted on Oct 13, 2008

csmock132
  • 4669 Answers

SOURCE: 1997 Bonneville - can't remove crankshaft pulley

You need a three jaw puller to remove the balancer. After you remove the center bolt the puller hooks into the three holes in the balancer.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: do not know how to remove crankshaft pulley to replace timeing belt

Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Posted on Jul 06, 2009

dmsr63
  • 2050 Answers

SOURCE: Broken crankshaft pully, need to know how to remove to replace

Normally...three bolts for the pulley assembly, and one large center bolt, and yes...a steering wheel puller will work, but make sure the puller doesn't sit into the center hole threads, or they will be destroyed. Sometimes a nut in here will prevent that.

Posted on Jul 28, 2009

ftw1952
  • 10319 Answers

SOURCE: I can't get the crankshaft damper pulley off.

Download this link and find your Service manual for your vehicle. It will serve you well and to keep for future reference

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove crankshaft pully from kia optima 2005 2.7 liter v6 24 val dohc ?


Remove all the belts on the pulley. Remove the center retaining bolt which typically needs to keep the engine from turning to get it off unless you use an impact wrench. Then you need a puller to push against the end of the crank shaft and pull the pulley off.

Sep 15, 2014 | 2005 Kia Optima

2 Answers

What is the normal oil pressure of an Isuzu crosswind gas engine


Not sure what a crosswind is, but normal oil pressure for most gasoline engines is 40 - 60psi depending on RPM and temp.

Jul 20, 2012 | 1999 Isuzu Trooper

1 Answer

Install water pump


you need a bolt type puller to remove crankshaft pulley go to auto parts store ask salesperson for bolt type puller used to remove crankshaft pulley harmonic balancer.

Dec 07, 2011 | 1997 Isuzu Rodeo

1 Answer

I'm trying to remove the crankshaft pully off of a 2000 Oldsmobile intrigue. I was able to remove the center bolt bolt the the pully doesn't have any holes to use a puller with how can I take it...


Attach the arms of the crankshaft pulley removal tool over the pulley and tighten the tool to the pulley using the tool's supplied bolts. Continue to tighten the tool using the bolts until the crankshaft pulley is pulled off the crankshaft. auto zone rents out tools for the job.

Oct 23, 2011 | Cars & Trucks

1 Answer

How to remove pully from crankshaft


Go to your local Autozone and rent a pulley puller. After removing the bolt from the center, use the pulley puller to pull the pulley off the end of the crankshaft.

Mar 06, 2011 | 1991 Isuzu Pickup

2 Answers

I am trying to locate the crankshaft sensor on a 92 pontiac bonneville se


It is by the crankshaft pulley.It is behind the pulley and you have to remove the pulley to replace it.There is a special tool for installing the new one.If you look through the pulley you should be able to see it.Hope this helps.Good luck.

Feb 24, 2010 | 1992 Pontiac Bonneville

1 Answer

Broken crankshaft pully, need to know how to remove to replace


Normally...three bolts for the pulley assembly, and one large center bolt, and yes...a steering wheel puller will work, but make sure the puller doesn't sit into the center hole threads, or they will be destroyed. Sometimes a nut in here will prevent that.

Jul 28, 2009 | 2003 Hyundai Santa Fe

1 Answer

Fab belt pully separated from crankshaft end.


replace crank pulley this is moulded to centre section of pulley when made

May 18, 2009 | 1993 Isuzu Trooper

1 Answer

Do 4runners crank pulleys go bad


Yes, in most cases you can. The crankshaft pulley is bolted to the front of the crank shaft by either 1 large bolt and thick washer, or by 4 small bolts around the edge of inside of the pulley, depending on model.

Remove all belts that are driven by the crankshaft pully and then grasp the pully to see if it is loose in some way.

To remove the large bolt(if that's what you have), will require the use of a strap wrench which can be gotten for the free loan-A-tool from Autozone.

Only if the end of the crankshaft was damaged in some way would you have to replace the crankshaft.


If you would like to contact me again about this or other problems, feel free to do so.
Bill
ASE Master Technician


Nov 17, 2008 | 2002 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...