Question about Ford Crown Victoria

Open Question

Engine takes a long time to start after cranking 1986 ford crown victoria 5.0 liter

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 102 Answers

SOURCE: how to trouble shoot starting system 98 ford crown victoria

Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Posted on Sep 23, 2009

  • 234 Answers

SOURCE: '96 ford Crown Victoria....No hazard or brake light no turn sigal

Sounds like the multifunction switch. Try working the hazard switch up and down a few times to see if you get some lights to work. If so then replace the switch.

Posted on Nov 09, 2009

drsinister69
  • 2317 Answers

SOURCE: How to change spark plugs and coil connector wires

Each coil mounts on top of the spark plug and is bolted down to the intake manifold with a 8mm bolt. You'll need to unplug the electrical connector to the coil, remove the 8mm bolt and pull the coil and boot up off the plug and out of the motor. You'll need a 5/8 inch spark plug socket, a ratchet and a 6 inch extension. Also a telescoping magnet with help getting the plug up out of the hole.

Posted on Apr 26, 2010

bigv198921
  • 1 Answer

SOURCE: 1992 crown vic 4.6l

Check the ground cable I had a bad ground on my 92 vic I replace the starter the battery then I found out the ground cable was bad replaced it and it starts prefect now

Posted on May 17, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions for replacing heater core in 1986 ford crown victoria LTD


Remove dash

disconnect heater core hoses in the engine compartment

open heater box, and remove the heater core.

Mar 01, 2014 | 1986 Ford Crown Victoria

1 Answer

2003 ford crown victoria turns over but wont crank


To clarify - the engine cranks but won't start, or the engine does not crank ?
What have you checked so far ?

Mar 01, 2013 | 2000 Ford Crown Victoria

1 Answer

Can a ford mustang 5.6 liter cylinder head go into a 2000 crown vic pi 4.6 liter with both heads bein different liters?


No. Also, displacement matters little, block casting is everything. example: small block 400CID heads and crank can go an a small block 350 end displacement is 383 due to longer stroke and combustion chamber.

Mar 14, 2012 | 2000 Ford Crown Victoria

2 Answers

My engine oil dipstick is missing on my 1999 ford crown victoria 5.6 liter engine what is the length of it so i can get a universal one


GO TO ANY AUTO PARTS STORE TELL THEM YOU HAVE 1999 FORD CROWN VICTORIA WITH A 4.6L ENGINE.THEY SHOULD HAVE A UNIVERAL OIL DIP STICK FOR YOUR CAR.

Feb 14, 2011 | 1988 Ford Crown Victoria

2 Answers

What is the cylinder order on an '89 5.0? Also, what is the spark plug order?


1989 Ford Crown Victoria 5.0 liter V-8 VIN "F"

2581dec.gif

Remember rated and comment this; good luck.

Aug 19, 2010 | 1989 Ford Crown Victoria

1 Answer

Where is the location of no. of cylinder on crown


2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"

a39c7f2.gif

Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

2 Answers

Just need info about changing transmission oil in 1996 Ford Crown Victoria LX. I'm not familiar with type of Transmission oil to use and how many quarts it holds and location of the drain plug.


You will need to drop the trans pan to drain. In turn you will need a trans filter kit which will include the filter and gasket. As far as fluid, it will require mercon dexron auto trans fluid, and will take about 6 quarts. What I normally do is fill with 5 qts and check, then add half qt at a time till full, which is normally 6 qts.

Oct 08, 2009 | 1996 Ford Crown Victoria

1 Answer

Engine does not start immediately when cranking


The problem could be many things. Is the engine light on? Check for proper fuel pressure. Remove one spark plug and inspect. Your vehicle may just need a simple tune up. Spark plugs,distributor cap and rotor,fuel filter.

Jul 26, 2009 | 1991 Ford LTD Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...