Question about Volkswagen Cars & Trucks

Open Question

2009 vw tiguan, fan switch only operates at highest speed

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: fan control switch

the blower resistor and pigtail will need to be replaced. good luck ive seen this problem a lot of times mr gm ha ha

Posted on Nov 23, 2008

Ad
  • 297 Answers

SOURCE: I have a 2001 vw jetta have a blower motor or fan

It is either the switch, or the resistor !

Posted on Aug 12, 2009

shocktroop40
  • 155 Answers

SOURCE: 2002 Honda Odyssey fan only works at high speed. The A/C compress

Usually when the blower fan only operates on hi speed, its because of a failed blower motor resistor. You still have hi speed because on hi, the power going to the blower motor goes directly to it, as opposed to the lower speeds, when the power is routed through the resistor, thus lowering the voltage, which in turn lowers the speed of the fan. The resistor is usually located near the blower motor itself, under the hood back near the firewall.

Posted on Aug 15, 2009

  • 10 Answers

SOURCE: oil change 2009 tiguan

even if they dont they should clean up there mess i would change dealers they dont seem to care about the small stuff if thats true what do you think there missing else where

Posted on Nov 07, 2009

  • 1565 Answers

SOURCE: 2005 Jeep Grand Cherokee. Htr/AC fan switch only

replace the blower motor resistor. It controls the fan speeds. It defaults to high speed only when it fails.

How to replace the blower motor resistor block: Caution: Stay clear of the blower motor and resistor block (Hot). Do not operate the blower motor with the resistor block removed. 1. Disconnect and isolate the battery negative cable.
2. Remove the glove box from the instrument panel.
3. Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch.
4. Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor.
5. Remove the two screws that secure the blower motor resistor block to the HVAC housing.
6. Remove the resistor block from the HVAC housing. Installation:
1. Position the blower motor resistor block into the HVAC housing.
2. Install the two screws that secure the resistor block to the HVAC housing. Tighten the screws to 2.2 Nm (20 in. lbs.)
3. Connect the wire harness connector to the resistor block.
4. Push in the lock on the blower motor resistor wire harness connecgtor to lock the connector latch.
5. Install the glove box.
6. Reconnect the battery negative cable.
7. Have a nice day!

Posted on Oct 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 vw tiguan intake carbon build-up


Sell your Tiguan. I had the intake clean done last Nov for the 3rd time. Last week in the fast lane car lost power and I was nearly killed. Today the VW tech tells me its carbon buildup again. I am dumping the Tiguan and going back to Japan again. PS I always use "Premium" why I dont know.

May 06, 2012 | Cars & Trucks

1 Answer

Unable to open gas tank on 2009 volkswagen tiguan


VW lock the gas tank with central locking
possibly the actuator stuck or dead
or the door not unlocked
try locking and unlocking all doors several times
and observe if all doors are responding
If all doors are locking and unlock the gas tank should also unlock
If not most likely the actuator or solenoid is bad
at 2009 this should be a warranty issue so let VW pay for it before you try it.

Hope this helps, it it does please leave feedback Thank You and Good Luck

Jan 01, 2011 | 2009 Volkswagen Tiguan

1 Answer

Howcanyoutellimportonvwtouran


I would imagine you could tell if a VW was imported or not by what units the speedo was in, km or mph.

http://en.wikipedia.org/wiki/Volkswagen_Tiguan

{ ... The production Tiguan was released at the 2007 Frankfurt Motor Show, and debuted as a 2008 model for Europe and elsewhere and in North America as a 2009 model. Sales of the Tiguan in Canada began in April 2008.
...
The import version of Tiguan appears on the Chinese market in 2009, but soon a locally built version (aka Shanghai-Volkswagen Tiguan) was revealed at 2009 Guangzhou Motor Show. The Chinese-built Tiguan uses 1.8TSI (118kW) and 2.0TSI (147kW), and has a revised front facia. At the same time the import Tiguan is still sold in China, which has 2.0TDI and R-Line kit as highlights. The basic design of the import model is the same as the international one. In order to differ locally-built and import models, Shanghai-VW Tiguan is given a Chinese name, known as ?? (tuguan), and the import one keeps the original letter name.
...}

Jul 10, 2010 | 2009 Volkswagen Tiguan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...