Question about Jeep Wrangler
I have a 92 wrangler 4.0 motor. Would not start. I could not hear the fuel pump cone on. I hit the tank with a hammer with the key on and I heard the pump start. So I had the pump replaced. The next day would not start, same thing as the first but hitting the tank did nothing this time. So the mechanic replaced the fuel pump relay and the rollover relay. I drove it home and went to start it and agin no start or fuel pump noise. I think the new pump is defective or bad connection, So I need help !!
Check the asd relay and computer out puts make sure they are working
Posted on Nov 01, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1999 GMC Jimmy won't start.
firstly where is fuel pump relay as i have never seen a GMC jimmy sorry about that but have you ever seen a foden ?? well the first thing is to check the fuse,if fuse is ok which can be checked by looking at it as its transparent or a piece of wire with a light bulb .across the battery.to find the relay is easy if you dont know where it is,When this piece of americana decides to work just turn ignition on and listen for the click of relay ,then when it doesnt start listen for click again or rather an absence of a click,sounds more like a dodgy pump in the tank or the connections going to it.when it wont start try thumping the fuel tank with the ignition on and if it is a sticky pump you might hear it start then at least you will know where the fault is.Another fault that i have come across with relays is that where the relay is passing a heavy load then its possibe for the contacts to burn inside the relay.When this happens then if it is possible to seperate the relay cover and clean the contacts with a points file (remember them ) or a piece of fine emery paper if the cover breaks taking it apart then use a bit of black insulating tape to repair the cover.Thats assuming the pump is in the tank and not bolted to the chassis near the fuel tank but that design with external pump i havent seen on a europeon car for nearly 20yrs .
Posted on Nov 05, 2008
check and see if you have an emergency shut off in the trunk. it will be on either side of the finder wall. it is there in case you get in a accident. the button pops up. make sure the button is in all the way. that shut off might be your problem.
Posted on Mar 02, 2009
Hey Tim take a look at this, will this help ?
No Engine Crank Or No Engine Start Due To Electronic Lockup Of The WCM / SKREEM
This bulletin involves the replacement of the Wireless Control Module (WCM), and if
equipped, the replacement of the Electric Steering Column Lock (ELV). The WCM is also
referred to as the Sentry Key Remote Entry Module (SKREEM).
The customer will experience a no engine crank AND a no engine start condition. Also, the
remote keyless entry (RKE) system will not operate. This condition may be due to an
electrostatic discharge (ESD) from the ignition key into the Wireless Control Module
(WCM), causing the WCM to electronically lockup. This condition may occur more
frequently in dry and/or cold weather conditions where a sufficient electrostatic charge is
more easily produced. This condition is corrected by the replacement of the WCM
1. With the condition present (i.e. the vehicle in the no crank / no start condition), connect
the StarSCAN® scan tool to the vehicle.
2. Turn the ignition switch to the “ON” position, and power up the StarSCAN®.
3. If the WCM is electronically locked up, the StarSCAN® will display the WCM as being
4. If the no crank / no start condition is present, and the WCM is “off bus”, then reset the
WCM by temporarily removing the IOD fuse (with the key out of the ignition switch),
wait for 10 seconds and then reinstall the IOD fuse.
5. With the IOD fuse reset having been performed, verify that the vehicle will now crank,
start, and run.
6. If the condition is temporarily corrected by performing the above steps, and if the part
number of the WCM is earlier than the part number of the WCM listed in the part
reference table in the Service Bulletin Parts Required Section below, then perform the
Posted on Jun 24, 2009
Tips for a great answer:
Oct 22, 2014 | Chevrolet TrailBlazer Cars & Trucks
Apr 16, 2011 | 2000 Dodge Dakota Quad Cab
Apr 12, 2011 | 1992 Dodge Dakota
Oct 16, 2009 | 1992 Toyota Camry V6
Aug 16, 2009 | 2000 Dodge Grand Caravan
Feb 06, 2009 | 1992 Ford Escort 4 Door
Dec 26, 2008 | 2004 Dodge Durango
Nov 17, 2008 | 2001 Chevrolet Blazer
Jul 31, 2008 | 2000 Chevrolet Astro
100 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: